闪光对焊钢筋连接工艺（Connecting process of flash butt welding reinforcing bar）.docVIP

下载本文档

2
0
约1.83万字
约 25页
2017-08-17 发布于河南
举报
版权申诉

闪光对焊钢筋连接工艺（Connecting process of flash butt welding reinforcing bar）.doc

1、原创力文档（book118）网站文档一经付费（服务费），不意味着购买了该文档的版权，仅供个人/单位学习、研究之用，不得用于商业用途，未经授权，严禁复制、发行、汇编、翻译或者网络传播等，侵权必究。。
2、本站所有内容均由合作方或网友上传，本站不对文档的完整性、权威性及其观点立场正确性做任何保证或承诺！文档内容仅供研究参考，付费前请自行鉴别。如您付费，意味着您自己接受本站规则且自行承担风险，本站不退款、不进行额外附加服务；查看《如何避免下载的几个坑》。如果您已付费下载过本站文档，您可以点击这里二次下载。
3、如文档侵犯商业秘密、侵犯著作权、侵犯人身权等，请点击“版权申诉”（推荐），也可以打举报电话：400-050-0827(电话支持时间：9:00-18:30)。
4、该文档为VIP文档，如果想要下载，成为VIP会员后，下载免费。
5、成为VIP后，下载本文档将扣除1次下载权益。下载后，不支持退款、换文档。如有疑问请联系我们。
6、成为VIP后，您将拥有八大权益，权益包括：VIP文档下载权益、阅读免打扰、文档格式转换、高级专利检索、专属身份标志、高级客服、多端互通、版权登记。
7、VIP文档为合作方或网友上传，每下载1次，网站将根据用户上传文档的质量评分、类型等，对文档贡献者给予高额补贴、流量扶持。如果你也想贡献VIP文档。上传文档

闪光对焊钢筋连接工艺（Connecting process of flash butt welding reinforcing bar）

闪光对焊钢筋连接工艺（Connecting process of flash butt welding reinforcing bar） Brief introduction of connecting process of flash butt welding bar Is the two flash butt welding of reinforcing steel bars are positioned in a docking form, using resistance welding current heat generated by two steel contact, the metal is melted to produce strong splash, formation of flash, quickly put a bonding method of forging force to complete, is a kind of resistance welding. 1 process 1 、 continuous flash butt welding Applicable to the smaller diameter of reinforcing steel and lower grade of steel bar, the upper limit diameter of welded steel bar can be determined according to the specific conditions of welding capacity and grade of steel bar, and shall conform to the provisions of table 4-10. Table 4-10 upper diameter of continuous flash welded reinforcement Welding capacity (KV * A) Reinforcement grade Diameter of reinforcement (mm) One hundred and sixty Grade I II III Twenty-five Twenty-two Twenty One hundred Grade I II III Twenty Eighteen Sixteen Eighty Grade I II III Sixteen Fourteen Twelve Process for continuous flash welding: welding machine for reinforced clamping in the jaw, after the power is switched on, the two reinforced end of local contact at the contact point of the steel bar in the high current density under the effect of rapid melting, evaporation, blasting, in high temperature granular metal from the weld seam in high speed flying out; when the contact point of the old after blasting, and the formation of new contact point, there is a continuous process of blasting, reinforced metal continuous feeding (at a feeding speed adapt to the process of welding, melting speed). Reinforced after a certain time of the burn, the weld reached the desired temperature, and heat diffusion to welding on both sides of the mouth, temperature, forming a certain width at this time, to be upset with considerable pressure, the liquid metal out of the weld, the weld reinforcement, and in the weld