桑塔纳2000gsi数据流（Santana 2000GSi data stream）.docVIP

下载本文档

4
0
约1.08万字
约 12页
2017-08-18 发布于河南
举报
版权申诉

桑塔纳2000gsi数据流（Santana 2000GSi data stream）.doc

1、原创力文档（book118）网站文档一经付费（服务费），不意味着购买了该文档的版权，仅供个人/单位学习、研究之用，不得用于商业用途，未经授权，严禁复制、发行、汇编、翻译或者网络传播等，侵权必究。。
2、本站所有内容均由合作方或网友上传，本站不对文档的完整性、权威性及其观点立场正确性做任何保证或承诺！文档内容仅供研究参考，付费前请自行鉴别。如您付费，意味着您自己接受本站规则且自行承担风险，本站不退款、不进行额外附加服务；查看《如何避免下载的几个坑》。如果您已付费下载过本站文档，您可以点击这里二次下载。
3、如文档侵犯商业秘密、侵犯著作权、侵犯人身权等，请点击“版权申诉”（推荐），也可以打举报电话：400-050-0827(电话支持时间：9:00-18:30)。
4、该文档为VIP文档，如果想要下载，成为VIP会员后，下载免费。
5、成为VIP后，下载本文档将扣除1次下载权益。下载后，不支持退款、换文档。如有疑问请联系我们。
6、成为VIP后，您将拥有八大权益，权益包括：VIP文档下载权益、阅读免打扰、文档格式转换、高级专利检索、专属身份标志、高级客服、多端互通、版权登记。
7、VIP文档为合作方或网友上传，每下载1次，网站将根据用户上传文档的质量评分、类型等，对文档贡献者给予高额补贴、流量扶持。如果你也想贡献VIP文档。上传文档

桑塔纳2000gsi数据流（Santana 2000GSi data stream）

桑塔纳2000gsi数据流（Santana 2000GSi data stream） Throttle angle: the normal value is 0~5 degrees at idle speed. If it is greater than 5 degrees, it is possible that the throttle control unit J338 does not make a basic adjustment of the system. The throttle cable is too tight, and the throttle control component is to be damaged 2. idle air quality measurements (manual transmission, N position): -1.70~+1.70g/s. If less than -1.70g/s, the throttle valve leaks; if greater than +1.70g/s, the intake system leaks 3. idle air quality measurements (automatic transmission D position): 0.00g/s (manual transmission is invalid). 4. working condition: when the engine is idle, idle speed should be displayed, or the idle switch should be checked. Display 05 (or 005) 1. engine speed: normal idle speed is 800 + 30rpm, if the idle speed exceeds the regulation, check idle speed. 2., idle speed regulation value: normal value is 800rpm, should remain unchanged. 3. idle speed control: normal value is -10%~+10%. 4. enter the air quality: idle speed, the normal value is 2.0~4.0g/s, if less than 2.0g/s, may intake system has leakage; greater than 4.0g/s, may the engine load is too large. Display 06 (or 006) 1. engine speed (measured value): normal idle speed is 800 + 30rpm, if the idle speed exceeds the regulation, check idle speed. 2. idle speed control: normal value is -10%~+10%. 3. mixing gas lambda control: normal value is -10%~+10%, if exceed the specified value, check lambda control. 4. ignition advance angle: when idle, the normal value is 12 + 4.5 degrees (BTDC). If less than 12 degrees (BTDC): excessive engine load Display 07 (or 007) 1. mixing gas lambda control: normal value is -10~+10%, if exceed the specified value, check lambda control. 2. lambda sensor voltage: normal value for this voltage, constantly changing between 0~1.0V. If the voltage is 0.1~0.3V: there is too much residual oxygen in the exhaust, the mixture is too thin; if the voltage is 0.7~1.0V: there is too little residua