选择浇口位置的技巧入水口选择（Selection of gate position techniques, inlet selection）.docVIP

下载本文档

1
0
约1.29万字
约 12页
2017-08-18 发布于河南
举报
版权申诉

选择浇口位置的技巧入水口选择（Selection of gate position techniques, inlet selection）.doc

1、原创力文档（book118）网站文档一经付费（服务费），不意味着购买了该文档的版权，仅供个人/单位学习、研究之用，不得用于商业用途，未经授权，严禁复制、发行、汇编、翻译或者网络传播等，侵权必究。。
2、本站所有内容均由合作方或网友上传，本站不对文档的完整性、权威性及其观点立场正确性做任何保证或承诺！文档内容仅供研究参考，付费前请自行鉴别。如您付费，意味着您自己接受本站规则且自行承担风险，本站不退款、不进行额外附加服务；查看《如何避免下载的几个坑》。如果您已付费下载过本站文档，您可以点击这里二次下载。
3、如文档侵犯商业秘密、侵犯著作权、侵犯人身权等，请点击“版权申诉”（推荐），也可以打举报电话：400-050-0827(电话支持时间：9:00-18:30)。
4、该文档为VIP文档，如果想要下载，成为VIP会员后，下载免费。
5、成为VIP后，下载本文档将扣除1次下载权益。下载后，不支持退款、换文档。如有疑问请联系我们。
6、成为VIP后，您将拥有八大权益，权益包括：VIP文档下载权益、阅读免打扰、文档格式转换、高级专利检索、专属身份标志、高级客服、多端互通、版权登记。
7、VIP文档为合作方或网友上传，每下载1次，网站将根据用户上传文档的质量评分、类型等，对文档贡献者给予高额补贴、流量扶持。如果你也想贡献VIP文档。上传文档

选择浇口位置的技巧入水口选择（Selection of gate position techniques, inlet selection）

选择浇口位置的技巧入水口选择（Selection of gate position techniques, inlet selection） Influence of gate on parts and selection of position I. requirements of gate location: 1. appearance requirements (gate traces, weld lines) 2. product functional requirements 3., mold processing requirements 4. warpage of products 5. gate is not easy to remove Two, the impact on production and function: The 1. flow (Flow, Length) determines the injection pressure, clamping force, and the product that is not filled Flow length shortening can reduce injection pressure and clamping force 2. gate position affects packing pressure Holding pressure size Packing pressure balance Keep the runner away from the future stress position of the product (such as the bearing) to avoid residual stress The location of the gate must be taken into account in order to avoid wind accumulation. Do not place the runner at the weaker or embedded position of the product to avoid bias (Core, Shaft) Three, select the gate position skills 1. placing the gate at the thickest part of the product, pouring from the thickest part can provide better filling and holding effect. If the pressure is not enough, the thinner areas will solidify faster in thicker areas Avoid placing the gate at a sudden change in thickness to avoid hysteresis or short shot 2., if possible, pour from the center of the product Placing the gate in the center of the product provides a length equal to the length of the flow The size of the flow length affects the injection pressure required The central pouring makes the packing pressure equal in all directions, and can avoid the uneven volume contraction 3 gate (Gate) The gate is a short slot with a small section of the cross section, used to connect the runner and the die. The cross sectional area is so small that the purpose is to obtain Following effects: 1. die cavity injection soon, the gate is cold junction 2., easy to remove water 3., only a few traces are left after the water outlet is completed 4. ma