cisco_asa防火墙恢复初始化（Cisco_asa firewall restore initialization）.docVIP

下载本文档

89
0
约4.5千字
约 8页
2017-08-21 发布于河南
举报
版权申诉

cisco_asa防火墙恢复初始化（Cisco_asa firewall restore initialization）.doc

1、本文档共8页，可阅读全部内容。
2、原创力文档（book118）网站文档一经付费（服务费），不意味着购买了该文档的版权，仅供个人/单位学习、研究之用，不得用于商业用途，未经授权，严禁复制、发行、汇编、翻译或者网络传播等，侵权必究。
3、本站所有内容均由合作方或网友上传，本站不对文档的完整性、权威性及其观点立场正确性做任何保证或承诺！文档内容仅供研究参考，付费前请自行鉴别。如您付费，意味着您自己接受本站规则且自行承担风险，本站不退款、不进行额外附加服务；查看《如何避免下载的几个坑》。如果您已付费下载过本站文档，您可以点击这里二次下载。
4、如文档侵犯商业秘密、侵犯著作权、侵犯人身权等，请点击“版权申诉”（推荐），也可以打举报电话：400-050-0827(电话支持时间：9:00-18:30)。
5、该文档为VIP文档，如果想要下载，成为VIP会员后，下载免费。
6、成为VIP后，下载本文档将扣除1次下载权益。下载后，不支持退款、换文档。如有疑问请联系我们。
7、成为VIP后，您将拥有八大权益，权益包括：VIP文档下载权益、阅读免打扰、文档格式转换、高级专利检索、专属身份标志、高级客服、多端互通、版权登记。
8、VIP文档为合作方或网友上传，每下载1次，网站将根据用户上传文档的质量评分、类型等，对文档贡献者给予高额补贴、流量扶持。如果你也想贡献VIP文档。上传文档

cisco_asa防火墙恢复初始化（Cisco_asa firewall restore initialization）

cisco_asa防火墙恢复初始化（Cisco_asa firewall restore initialization） ASA firewall flash is deleted Firewall starts again Use, BREAK, or, ESC, to, interrupt, boot. Use, SPACE, to, begin, boot, immediately. Press ESC to enter monitor mode There is no difference between display and switch routers in monitor mode. Command format is also very similar, as long as everyone changes, it is not difficult to recover. Rommon #1? Variables:, Use, sync, to, store, in, NVRAM ADDRESS=, addr, local, IP, address CONFIG=, name, config, file, path/name GATEWAY=, addr, gateway, IP, address IMAGE=, name, image, file, path/name LINKTIMEOUT=, num, Link, UP, timeout (seconds) PKTTIMEOUT=, num, packet, timeout (seconds) PORT=, name, Ethernet, interface, port RETRY=, num, Packet, Retry, Count (Ping/TFTP) SERVER=, addr, server, IP, address VLAN=, num, enable/disable, DOT1Q, tagging, on, the, selected, port Rommon #2 ADDRESS= (because the TFFP is uploaded, so the firewall is set as a client) Rommon #3 GATEWAY= (Gateway) Rommon #4 IMAGE=asa802-k8.bin (import the name of IOS) Rommon #5 SERVER= (server IP, that is, your PC) Rommon, #6, sync (save) Updating NVRAM Parameters... Rommon #7 Ping Sending 20, 100-byte, ICMP, Echoes, to, , timeout, is, 4, seconds: ?!!!!!!!!!!!!!!!!!!! Success rate is 95 percent (19/20) Confirm whether the line is connected, open the TFTP software (here shows that my test is ASA5505, so the E0/0 port. I dont know what the device should be. I can use set to see PORT=Ethernet0/0 Rommon #8 tftpdnld (upload) ROMMON Variable Settings: ADDRESS= SERVER= GATEWAY= PORT=Ethernet0/0 VLAN=untagged IMAGE=asa802-k8.bin CONFIG= LINKTIMEOUT=20 PKTTIMEOUT=4 RETRY=20 TFTP asa802-k8.bin@ via !!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!! After import, the device is restarted. Now IOS has access Type, help, or , for, a, list, of, available, commands. Ciscoasa en But now IOS is not loaded, but boot boot devices from the TFTP, and the TFTP server disconnects from the new monitoring mode. This can