压铸机故障分析（Fault analysis of die casting machine）.docVIP

下载本文档

3
0
约2万字
约 20页
2017-08-23 发布于河南
举报
版权申诉

压铸机故障分析（Fault analysis of die casting machine）.doc

1、原创力文档（book118）网站文档一经付费（服务费），不意味着购买了该文档的版权，仅供个人/单位学习、研究之用，不得用于商业用途，未经授权，严禁复制、发行、汇编、翻译或者网络传播等，侵权必究。。
2、本站所有内容均由合作方或网友上传，本站不对文档的完整性、权威性及其观点立场正确性做任何保证或承诺！文档内容仅供研究参考，付费前请自行鉴别。如您付费，意味着您自己接受本站规则且自行承担风险，本站不退款、不进行额外附加服务；查看《如何避免下载的几个坑》。如果您已付费下载过本站文档，您可以点击这里二次下载。
3、如文档侵犯商业秘密、侵犯著作权、侵犯人身权等，请点击“版权申诉”（推荐），也可以打举报电话：400-050-0827(电话支持时间：9:00-18:30)。
4、该文档为VIP文档，如果想要下载，成为VIP会员后，下载免费。
5、成为VIP后，下载本文档将扣除1次下载权益。下载后，不支持退款、换文档。如有疑问请联系我们。
6、成为VIP后，您将拥有八大权益，权益包括：VIP文档下载权益、阅读免打扰、文档格式转换、高级专利检索、专属身份标志、高级客服、多端互通、版权登记。
7、VIP文档为合作方或网友上传，每下载1次，网站将根据用户上传文档的质量评分、类型等，对文档贡献者给予高额补贴、流量扶持。如果你也想贡献VIP文档。上传文档

压铸机故障分析（Fault analysis of die casting machine）

压铸机故障分析（Fault analysis of die casting machine） Common troubles and elimination methods of die casting machine When the die casting machine fails to work in the course of its work, the operator should pay high attention to it, and observe it calmly, judge the location of the fault and the possible cause, and determine a feasible method of maintenance. The operator must be reminded that the work procedure should be worked out, and no violation shall be taken so as to avoid further accidents. To deal with the machine failure, both the cold chamber die casting machine and the hot chamber die casting machine can be carried out according to the following procedures: 1) judge the symptoms and location of the fault by looking, listening, and testing. 2) analyze the possible causes of the failure. 3) look up the equipment operation record and trouble file. 4) determine the corresponding processing methods and working procedures. 5) hands-on maintenance. I. the oil pump can not start Inspection and analysis: press the starting button of the oil pump to observe whether the motor relay is pulled or not. 1, if the relay does not attract, then check 1) whether the motor thermal relay is operated or damaged. 2) the power supply circuit is normal (check with a multimeter). 3) whether the contact of the starting and stopping button is normal and whether the control line is broken or not. 4) whether the relay coil is damaged (check with a multimeter). 2, if the pump starts, the relay is attracted, then check 1) whether the oil pump is damaged or jammed. 2) is the line of the relay to the motor normal?. 3) is the pump damaged or assembled too tight?. Hand pull shaft coupling should be easy, axial movement of the coupling should be about 3 ~ 5mm clearance for the appropriate. Two. Press the starting button of the oil pump and heat the relay to trip Check and analyze: press the starting button of the oil pump, and the hot relay is tripped. This is related to the current, the load and th