广数990ma数控系统调试应注意的几个问题（Several problems should be paid attention to in debugging CNC 990ma system）.docVIP

下载本文档

38
0
约6.12千字
约 5页
2017-08-31 发布于河南
举报
版权申诉

广数990ma数控系统调试应注意的几个问题（Several problems should be paid attention to in debugging CNC 990ma system）.doc

1、原创力文档（book118）网站文档一经付费（服务费），不意味着购买了该文档的版权，仅供个人/单位学习、研究之用，不得用于商业用途，未经授权，严禁复制、发行、汇编、翻译或者网络传播等，侵权必究。。
2、本站所有内容均由合作方或网友上传，本站不对文档的完整性、权威性及其观点立场正确性做任何保证或承诺！文档内容仅供研究参考，付费前请自行鉴别。如您付费，意味着您自己接受本站规则且自行承担风险，本站不退款、不进行额外附加服务；查看《如何避免下载的几个坑》。如果您已付费下载过本站文档，您可以点击这里二次下载。
3、如文档侵犯商业秘密、侵犯著作权、侵犯人身权等，请点击“版权申诉”（推荐），也可以打举报电话：400-050-0827(电话支持时间：9:00-18:30)。
4、该文档为VIP文档，如果想要下载，成为VIP会员后，下载免费。
5、成为VIP后，下载本文档将扣除1次下载权益。下载后，不支持退款、换文档。如有疑问请联系我们。
6、成为VIP后，您将拥有八大权益，权益包括：VIP文档下载权益、阅读免打扰、文档格式转换、高级专利检索、专属身份标志、高级客服、多端互通、版权登记。
7、VIP文档为合作方或网友上传，每下载1次，网站将根据用户上传文档的质量评分、类型等，对文档贡献者给予高额补贴、流量扶持。如果你也想贡献VIP文档。上传文档

广数990ma数控系统调试应注意的几个问题（Several problems should be paid attention to in debugging CNC 990ma system）

广数990ma数控系统调试应注意的几个问题（Several problems should be paid attention to in debugging CNC 990ma system） For some time has been debugging machine tools, the system used for the wide number of 990MA milling system (four axis four linkage), there are some experience, written out for interested persons reference, wrong or understanding of errors, hope expert advice. 1.plc parameter: after the PLC parameter is modified, press the s key to save. This is different from the other parameters and will be saved automatically after other parameters are modified; 2. the setting of electronic gear: Calculation of A. electronic gear ratio When the system parameters I. (bit) 005.2=0: the smallest mobile units of 0.001mm, 0.001deg, G= frequency divider / molecular denominator =n * c * 4/ input pulse: such as motor and lead screw directly connected to 10mm command pulse was 10000 G=1 * 2500 * 4/10000=1; type can be written as a simplified formula g=: (10 / screw guide) x gear ratio. When the system parameters ii. (bit) 005.2=1: (smallest mobile units 0.0001mm, 0.0001deg) when the formula can be written as a simplified formula: g= (10 83019 (screw * 10)) x gear ratio. III. g= for rotating shaft (1 / 36)) * reduction ratio. IV. settings: the electronic gear ratio is set in the drive. However, when the denominator value is large, it is set in the system. Otherwise, the location is not correct. It may be the reason why the NC system does not match the speed of the drive. 3. new version of PLC, r255.0 instead of r510.0 as the first scan cycle pulse signal. 4., increase the system parameter range, method: enter the system parameter interface, select the parameters to be modified, press the conversion button, appear Min, Max two parameters, modify, and then press the conversion key, The parameter range of the system is modified successfully, and the parameter setting value can be further modified. 5. the system is prone to power loss when the system parameters are missing or modified by default p