pcb设计的基本原则要求)（Basic requirements of PCB design)）.docVIP

下载本文档

11
0
约9.34千字
约 7页
2017-09-01 发布于河南
举报
版权申诉

pcb设计的基本原则要求)（Basic requirements of PCB design)）.doc

1、原创力文档（book118）网站文档一经付费（服务费），不意味着购买了该文档的版权，仅供个人/单位学习、研究之用，不得用于商业用途，未经授权，严禁复制、发行、汇编、翻译或者网络传播等，侵权必究。。
2、本站所有内容均由合作方或网友上传，本站不对文档的完整性、权威性及其观点立场正确性做任何保证或承诺！文档内容仅供研究参考，付费前请自行鉴别。如您付费，意味着您自己接受本站规则且自行承担风险，本站不退款、不进行额外附加服务；查看《如何避免下载的几个坑》。如果您已付费下载过本站文档，您可以点击这里二次下载。
3、如文档侵犯商业秘密、侵犯著作权、侵犯人身权等，请点击“版权申诉”（推荐），也可以打举报电话：400-050-0827(电话支持时间：9:00-18:30)。
4、该文档为VIP文档，如果想要下载，成为VIP会员后，下载免费。
5、成为VIP后，下载本文档将扣除1次下载权益。下载后，不支持退款、换文档。如有疑问请联系我们。
6、成为VIP后，您将拥有八大权益，权益包括：VIP文档下载权益、阅读免打扰、文档格式转换、高级专利检索、专属身份标志、高级客服、多端互通、版权登记。
7、VIP文档为合作方或网友上传，每下载1次，网站将根据用户上传文档的质量评分、类型等，对文档贡献者给予高额补贴、流量扶持。如果你也想贡献VIP文档。上传文档

pcb设计的基本原则要求)（Basic requirements of PCB design)）

pcb设计的基本原则要求)（Basic requirements of PCB design)） Analog signals and digital signals must be returned to the ground, because the digital signal changes rapidly, so that the noise caused by the digital ground will be very large, and analog signals need a clean reference work. If the analog and digital mix together, the noise will affect the analog signal. In general, analog and digital are to be separately handled and then joined together by fine wire or single point together. The general idea is to try to block the noise from the digital ground to simulate the ground. Of course, this is not a very strict requirement. Analog and digital must be separated. If the numbers near the analog part are still very clean, they can be put together. I. Basic requirements for PCB design Size principle of 1.PCB board In the PCB design, determine the size of the board is the most important, no matter what kind of electronic products, it is the size of the PCB panels are subjected to the shell or the size of the box, inside of the housing can not exceed the range of it is reserved. 2, PCB and external components of the connection PCB and external components are usually connected by plastic wires or metal insulated wires. But sometimes it is also designed as a socket, that is, a plug-in printed circuit board is installed inside the device to provide a contact position for the socket. For larger components mounted on the printed circuit board, metal fittings shall be attached to improve vibration resistance and impact resistance. 3, PCB wiring diagram design principles We need to select components and various socket specifications, size, area and have a complete understanding of the position of each component; arrange the reasonable and careful consideration, mainly from the angle of electromagnetic compatibility, anti-interference, short line, cross, power supply, the path and decoupling etc. consider. After the location of each component is determined, each component is connected on-