热敏电阻的长线测量抗干扰方法（Long term measurement anti-interference method for thermistor）.docVIP

下载本文档

6
0
约2.18万字
约 17页
2017-09-02 发布于河南
举报
版权申诉

热敏电阻的长线测量抗干扰方法（Long term measurement anti-interference method for thermistor）.doc

1、原创力文档（book118）网站文档一经付费（服务费），不意味着购买了该文档的版权，仅供个人/单位学习、研究之用，不得用于商业用途，未经授权，严禁复制、发行、汇编、翻译或者网络传播等，侵权必究。。
2、本站所有内容均由合作方或网友上传，本站不对文档的完整性、权威性及其观点立场正确性做任何保证或承诺！文档内容仅供研究参考，付费前请自行鉴别。如您付费，意味着您自己接受本站规则且自行承担风险，本站不退款、不进行额外附加服务；查看《如何避免下载的几个坑》。如果您已付费下载过本站文档，您可以点击这里二次下载。
3、如文档侵犯商业秘密、侵犯著作权、侵犯人身权等，请点击“版权申诉”（推荐），也可以打举报电话：400-050-0827(电话支持时间：9:00-18:30)。
4、该文档为VIP文档，如果想要下载，成为VIP会员后，下载免费。
5、成为VIP后，下载本文档将扣除1次下载权益。下载后，不支持退款、换文档。如有疑问请联系我们。
6、成为VIP后，您将拥有八大权益，权益包括：VIP文档下载权益、阅读免打扰、文档格式转换、高级专利检索、专属身份标志、高级客服、多端互通、版权登记。
7、VIP文档为合作方或网友上传，每下载1次，网站将根据用户上传文档的质量评分、类型等，对文档贡献者给予高额补贴、流量扶持。如果你也想贡献VIP文档。上传文档

热敏电阻的长线测量抗干扰方法（Long term measurement anti-interference method for thermistor）

热敏电阻的长线测量抗干扰方法（Long term measurement anti-interference method for thermistor） The introduction of interference compensation circuit 1. The interference in the long term will cause oscillation, because your sampling is the current value, the interference can be equivalent to the current. 2. The R1 Series in the constant current source, the interference current through R1, the interference equivalent to the change of the constant current source is offset. 3. High frequency interference exists in the form of voltage measurement, and your speed is only 100Hz, easily filtered, as long as the detection circuit in a filter can. 4. It is recommended to use 4 line bridge connection (4 terminal resistance type), 3 wire connection in the strong interference environment may be a problem, because the 3 line method has an implicit assumption that the lead resistance bridge arm resistance, strong interference in the environment, long-term inductance tends to lead impedance into large multiplication. Youre not using the bridge You should not use the bridge is wrong, the first signal acquisition circuit you depend entirely on Yu Heng current source, a slight fluctuation will produce great error, in addition to being a good constant current source is also very easy. It is recommended that you may be the one on the bridge on the arm PT100. In addition, the problem of the hardware software can also be solved, for example, the temperature curve of PT is regular, we can design a compensation table on the ROM in the program design, according to the temperature measured by the look-up table for compensation value. In addition, you said that volatility is likely to be your constant current source caused by the fluctuation of. Thank you I did not use the bridge, mainly because of the bridge temperature Thank you I did not use the bridge, mainly because of the power supply to the temperature range of bridge and bridge have limited requirement. We are modifying the printed circuit board based