雕刻机运动板卡资料（Engraving machine movement card data）.docVIP

下载本文档

11
0
约6.92千字
约 7页
2017-09-02 发布于河南
举报
版权申诉

雕刻机运动板卡资料（Engraving machine movement card data）.doc

1、原创力文档（book118）网站文档一经付费（服务费），不意味着购买了该文档的版权，仅供个人/单位学习、研究之用，不得用于商业用途，未经授权，严禁复制、发行、汇编、翻译或者网络传播等，侵权必究。。
2、本站所有内容均由合作方或网友上传，本站不对文档的完整性、权威性及其观点立场正确性做任何保证或承诺！文档内容仅供研究参考，付费前请自行鉴别。如您付费，意味着您自己接受本站规则且自行承担风险，本站不退款、不进行额外附加服务；查看《如何避免下载的几个坑》。如果您已付费下载过本站文档，您可以点击这里二次下载。
3、如文档侵犯商业秘密、侵犯著作权、侵犯人身权等，请点击“版权申诉”（推荐），也可以打举报电话：400-050-0827(电话支持时间：9:00-18:30)。
4、该文档为VIP文档，如果想要下载，成为VIP会员后，下载免费。
5、成为VIP后，下载本文档将扣除1次下载权益。下载后，不支持退款、换文档。如有疑问请联系我们。
6、成为VIP后，您将拥有八大权益，权益包括：VIP文档下载权益、阅读免打扰、文档格式转换、高级专利检索、专属身份标志、高级客服、多端互通、版权登记。
7、VIP文档为合作方或网友上传，每下载1次，网站将根据用户上传文档的质量评分、类型等，对文档贡献者给予高额补贴、流量扶持。如果你也想贡献VIP文档。上传文档

雕刻机运动板卡资料（Engraving machine movement card data）

雕刻机运动板卡资料（Engraving machine movement card data） Question 1 Q: when I use the SV control card to control the servo motor, when I turn on the servo motor, I turn it off. Excuse me, whats the reason for this? A: there may be several main reasons for the motor flying: 1., the encoder direction of the control card is wrong, forming a positive feedback control, causing the motor to fly. Solution: inverting encoder A and B. 2., servo motor parameter setting error, such as Panasonic servo motor is set in the reverse direction, will also cause the motor to fly. Solution: modify the direction of motion of the drive. Question 2 Q: when you use the ISA bus control card under Windows, when you begin to enter the demo program, the system always prompts the control card to open failure. What is the reason for that? A: This shows that the communication between the control card and the computer is not set up. This may be caused by the following reasons: 1., if you dont have the ISA (PCI) card driver installed, you first install the driver. 2. first of all, you should turn off the computer and check if the contact between the control card and the ISA (PCI) slot is good. 3. check the control card jumper is correct, JP1 jumper generally select the default address (0X300) 4. in the DEMO directory, there are GTCmd.ini configuration files, you need to do the corresponding settings of the board. 5., if the above method is implemented, the board still can not work, contact the hi tech companys Technical Services Department consultation Question 3 Q: when I was installing the PCI bus control card, the system indicated that I could not find the device driver. Whats the reason for that? A: please try changing slots, cleaning the gold fingers or using the computer after you change it. Question 4 Q: I use the Windows2000 PCI control card, driver board installed successfully, using normal, but when I reboot, enter the demo program, the system does not prompt the PCI device, PCI device failed to o