powerpcb 快捷命令(Powerpcb shortcut command).docVIP

powerpcb 快捷命令(Powerpcb shortcut command).doc

  1. 1、原创力文档(book118)网站文档一经付费(服务费),不意味着购买了该文档的版权,仅供个人/单位学习、研究之用,不得用于商业用途,未经授权,严禁复制、发行、汇编、翻译或者网络传播等,侵权必究。。
  2. 2、本站所有内容均由合作方或网友上传,本站不对文档的完整性、权威性及其观点立场正确性做任何保证或承诺!文档内容仅供研究参考,付费前请自行鉴别。如您付费,意味着您自己接受本站规则且自行承担风险,本站不退款、不进行额外附加服务;查看《如何避免下载的几个坑》。如果您已付费下载过本站文档,您可以点击 这里二次下载
  3. 3、如文档侵犯商业秘密、侵犯著作权、侵犯人身权等,请点击“版权申诉”(推荐),也可以打举报电话:400-050-0827(电话支持时间:9:00-18:30)。
  4. 4、该文档为VIP文档,如果想要下载,成为VIP会员后,下载免费。
  5. 5、成为VIP后,下载本文档将扣除1次下载权益。下载后,不支持退款、换文档。如有疑问请联系我们
  6. 6、成为VIP后,您将拥有八大权益,权益包括:VIP文档下载权益、阅读免打扰、文档格式转换、高级专利检索、专属身份标志、高级客服、多端互通、版权登记。
  7. 7、VIP文档为合作方或网友上传,每下载1次, 网站将根据用户上传文档的质量评分、类型等,对文档贡献者给予高额补贴、流量扶持。如果你也想贡献VIP文档。上传文档
查看更多
powerpcb 快捷命令(Powerpcb shortcut command)

powerpcb 快捷命令(Powerpcb shortcut command) PowerPCB shortcut command brief introduction PowerPCB provides users with a set of quick commands. Quick commands are used primarily for operations that require frequent changes in the design process, such as changing line widths, wiring layers, changing design, Grid, and so on through quick commands. The shortcut command operation is as follows: enter the command string from the keyboard, enter the value in the format, and then enter the enter key. If you change the current layer, just enter the shortcut command L from the keyboard, and then enter the new routing layer (such as Figure 2), and finally enter the Enter key to complete, very convenient. Here is a quick command of Chinese explanations for your reference Global settings command Command characters, commands, meanings, and uses C format, used to display the Thermal pad and Plane layer in the inner film design. The method of use is to enter C display from the keyboard, and then input C to remove the display. D opens / closes the current layer display. The method is to switch D from the keyboard. The proposed design uses D to Display Current, Layer, Last = ON. . DO through hole outline display switching. When ON, the aperture is highlighted, and the pad is displayed in the bottom tone. The way to use it is to switch DO from the keyboard. E wiring termination mode switching, in the following 3 ways to switch between. In End, No, Via wiring, the wiring is terminated without VIA when Ctrl+ hits In End Via wiring, when Ctrl+ hits, the wiring terminates in VIA mode When Ctrl+ Test Point wiring, End click, wiring to test PIN VIA termination The way to use it is to switch E from the keyboard. I database integrity testing, the design process found the system exception, you can try to hit this key. L n changes the current layer to the new n layer n can be numeric or a name, such as (L 2) or (L, top). The N s is used to highlight the NET, s as the signal name to display. You ca

您可能关注的文档

文档评论(0)

jgx3536 + 关注
实名认证
文档贡献者

该用户很懒,什么也没介绍

版权声明书
用户编号:6111134150000003

1亿VIP精品文档

相关文档