联想电脑怎样安装ghost系统处理方法（How does Lenovo computer install ghost system）.doc

下载文档 降价啦

4
0
约8.17千字
约 8页
2017-09-03 发布于河南
举报
版权申诉
保障服务

联想电脑怎样安装ghost系统处理方法（How does Lenovo computer install ghost system）.doc

1、本文档共8页，可阅读全部内容。
2、原创力文档（book118）网站文档一经付费（服务费），不意味着购买了该文档的版权，仅供个人/单位学习、研究之用，不得用于商业用途，未经授权，严禁复制、发行、汇编、翻译或者网络传播等，侵权必究。
3、本站所有内容均由合作方或网友上传，本站不对文档的完整性、权威性及其观点立场正确性做任何保证或承诺！文档内容仅供研究参考，付费前请自行鉴别。如您付费，意味着您自己接受本站规则且自行承担风险，本站不退款、不进行额外附加服务；查看《如何避免下载的几个坑》。如果您已付费下载过本站文档，您可以点击这里二次下载。
4、如文档侵犯商业秘密、侵犯著作权、侵犯人身权等，请点击“版权申诉”（推荐），也可以打举报电话：400-050-0827(电话支持时间：9:00-18:30)。

联想电脑怎样安装ghost系统处理方法（How does Lenovo computer install ghost system）

联想电脑怎样安装ghost系统处理方法（How does Lenovo computer install ghost system） The reason is the computer OEM authentication information Lenovo motherboard has embedded, general recommendations or the original installation, trying to upgrade, the most stable of such a system, if you need to install the GHOST version you can try the following one way: 1. use GHOST11.5 package disk, install try 2. with the original installation disk re partition, and then install the system, until the end and then the lattice C, remove the disc with GHOST installed on OK [in the motherboard BIOS set the hard disk for the ATA mode, or IDE mode, also some motherboard shows the compatibility mode, do not choose AHCI mode, because most of the system disk does not support this model. Then you can set for compatibility with a disk, use the setup disk format, then GHOST format after DISKGEN setup boot partition is activated, finally directly to GHOST OK. 3. uninstall Lenovo comes with a key recovery, you have to install version try 4. enter with PE system and install under PE 5.BIOS set SATA MODE to IDE mode After careful investigation, verification, found that its hard drive, CD-ROM are serial port, consider repeatedly, decided to replace the IDE interface for CD-ROM drive. Install GHOST... Problem solving!! Thank you.... Summarize the problem that several computers can not install GHOST system One. Use SATA drive model: If the motherboard is a Intel chipset, it can be resolved by modifying the CMOS settings, as follows: 1.AMI BIOS: boot, press Del to enter the CMOS settings, and then select Advanced - IDE Configuration, the ATA/IDE Configuration to Combined, save exit. 2.Award BIOS: boot, press Del to enter the CMOS settings, and then select Integrated Peripherals - OnChip IDE Device, the On-Chip Seriel ATA item changed to Combined Mode. If not yet (mainly the CD-ROM and hard disk are all SATA interfaces), change to SATA Only. Save exit. (such as XMG2000, XRD1000, etc.) If the motherboard uses VIA, nV