ppr管的规格标识（Specification specification for PPR tubes）.docVIP

下载本文档

4
0
约4.94千字
约 6页
2017-09-05 发布于河南
举报
版权申诉

ppr管的规格标识（Specification specification for PPR tubes）.doc

1、本文档共6页，可阅读全部内容。
2、原创力文档（book118）网站文档一经付费（服务费），不意味着购买了该文档的版权，仅供个人/单位学习、研究之用，不得用于商业用途，未经授权，严禁复制、发行、汇编、翻译或者网络传播等，侵权必究。
3、本站所有内容均由合作方或网友上传，本站不对文档的完整性、权威性及其观点立场正确性做任何保证或承诺！文档内容仅供研究参考，付费前请自行鉴别。如您付费，意味着您自己接受本站规则且自行承担风险，本站不退款、不进行额外附加服务；查看《如何避免下载的几个坑》。如果您已付费下载过本站文档，您可以点击这里二次下载。
4、如文档侵犯商业秘密、侵犯著作权、侵犯人身权等，请点击“版权申诉”（推荐），也可以打举报电话：400-050-0827(电话支持时间：9:00-18:30)。
5、该文档为VIP文档，如果想要下载，成为VIP会员后，下载免费。
6、成为VIP后，下载本文档将扣除1次下载权益。下载后，不支持退款、换文档。如有疑问请联系我们。
7、成为VIP后，您将拥有八大权益，权益包括：VIP文档下载权益、阅读免打扰、文档格式转换、高级专利检索、专属身份标志、高级客服、多端互通、版权登记。
8、VIP文档为合作方或网友上传，每下载1次，网站将根据用户上传文档的质量评分、类型等，对文档贡献者给予高额补贴、流量扶持。如果你也想贡献VIP文档。上传文档

ppr管的规格标识（Specification specification for PPR tubes）

ppr管的规格标识（Specification specification for PPR tubes） PPR tube spec: DN15, DN20, DN25 is the outside diameter. In charge of four and six in charge of the diameter 1 inches =25.4 mm =8 points 1/2 is four points (4 points) DN15 3/4 is six points (6 points) DN20 2 in charge of DN8 4 in charge of DN15 6 in charge of DN20 1 DN25 1.2 DN32 1.5 DN40 2 DN50 2.5 DN65 3 DN80 4 DN100 5 DN125 6 DN150 8 DN200 10 DN250 12 DN300 GB/T50106-2001 2.4 diameter 2.4.1 diameter should be mm units. Expression of 2.4.2 in diameter shall comply with the following provisions: 1 water gas delivery pipe (galvanized or non Galvanized), cast iron pipes and other pipes, pipe diameter should be nominal diameter DN; Welded steel pipe seamless steel pipe (2, straight or spiral seam), copper pipe, stainless steel pipe, pipe diameter, outer diameter and thickness should be said; 3 reinforced concrete (or concrete) pipe, clay pipe, acid resistant ceramic tube, pipe and other pipe diameter should be gangwa, with inner diameter of D said; 4 plastic pipe, the diameter should be expressed by the method of product standards; 5 when design with nominal diameter DN diameter, its nominal diameter is DN and the corresponding product specification table. The building water supply and drainage with a hard polyvinyl chloride pipe specifications with de (nominal diameter) * e (nominal wall thickness) said (GB 5836.1-92) Standard Specification for PPR pipe pipe series S, nominal diameter DN * nominal wall thickness en For example: PPR S5, PPR series pipe nominal diameter dn25mm, nominal wall thickness PPR en2.5mm Said S5, DN25 * en2.5mm PPR series: S tube is used to represent the dimensionless numerical series of PPR pipe specifications, as S= (dn-en) / 2 EN Where: DN - PPR nominal diameter, unit is mm En - PPR nominal wall thickness, the unit is mm The commonly used PP-R pipe specifications are 5, 4, 3.2, 2.5, 2, five series PPR pipe PPR pipe specifications according to the standard size rate SDR value were 11, 9, 7.