丝印pcb常见质量问题原因分析（Analysis of common quality problems in screen printing PCB）.docVIP

下载本文档

5
0
约1.58万字
约 10页
2017-09-05 发布于河南
举报
版权申诉

丝印pcb常见质量问题原因分析（Analysis of common quality problems in screen printing PCB）.doc

1、原创力文档（book118）网站文档一经付费（服务费），不意味着购买了该文档的版权，仅供个人/单位学习、研究之用，不得用于商业用途，未经授权，严禁复制、发行、汇编、翻译或者网络传播等，侵权必究。。
2、本站所有内容均由合作方或网友上传，本站不对文档的完整性、权威性及其观点立场正确性做任何保证或承诺！文档内容仅供研究参考，付费前请自行鉴别。如您付费，意味着您自己接受本站规则且自行承担风险，本站不退款、不进行额外附加服务；查看《如何避免下载的几个坑》。如果您已付费下载过本站文档，您可以点击这里二次下载。
3、如文档侵犯商业秘密、侵犯著作权、侵犯人身权等，请点击“版权申诉”（推荐），也可以打举报电话：400-050-0827(电话支持时间：9:00-18:30)。
4、该文档为VIP文档，如果想要下载，成为VIP会员后，下载免费。
5、成为VIP后，下载本文档将扣除1次下载权益。下载后，不支持退款、换文档。如有疑问请联系我们。
6、成为VIP后，您将拥有八大权益，权益包括：VIP文档下载权益、阅读免打扰、文档格式转换、高级专利检索、专属身份标志、高级客服、多端互通、版权登记。
7、VIP文档为合作方或网友上传，每下载1次，网站将根据用户上传文档的质量评分、类型等，对文档贡献者给予高额补贴、流量扶持。如果你也想贡献VIP文档。上传文档

丝印pcb常见质量问题原因分析（Analysis of common quality problems in screen printing PCB）

丝印pcb常见质量问题原因分析（Analysis of common quality problems in screen printing PCB） This paper contributed by liangziheng201. Doc document may at the WAP end of the browsing experience poor. Suggest you select TXT, or download the source file to the machine view. Analysis of the causes of common quality problems of screen printing The reason the printing accuracy deviation of 1. in the production of multicolor overprint (half tone printing) of the screen, the screen in different temperature drying, thus causing the printing accuracy error. The 2. version of the low tension or overprint (halftone) screen tension. 3. the use of blowing drying, uneven drying screen jane. 4. is too old, not strong and the deformation of the frame plate, due to poor stability due to screen frame printing image deviation (which can be used to detect the film) 5. multicolor overprint, use the network distance to a. 6. squeegee deformation. 7. are some factors that cause the substrate size change of the moire 1. halftone printing screen and the screen mesh collocation error (screen number is 2.5 in line, 3.75 or 6.25 times). 2. half tone screen and screen printing line angle error. The 3.RZ value is too high (less than 8). 4. templates are too thick or too thin. 5. and the line size is too small, the dot will lose (dot range should be in 5 - 95%). The cause of color change 1. due to evaporation of the solvent leads to the ink consistency change (different viscosity). 2. changes in the process of printing squeegee angle. 3. changes in the process of printing squeegee hardness. Change in the rate of 4. in the printing process. 5. squeegee edge damage. The cause of premature failure of the 1. template gum problems. 2. exposure before drying defects. The exposure time is less than 3. 4. the net margin is too high. 5. ink dry sharp knife, the pressure is too large. 6. the use of cleaning solvents for cleaning errors (including a small amount of water). Common problems and solutions of the printed circui