液晶显示电子钟c程序.docVIP

? ? ?? 可遥控校对时间，用1206液晶显示（r/w接地），能自动进行闰年补偿，程序如下（红外接收输出管脚接单片机外部中断0）如发现错误，请指正 还可以加入闹钟的程序 #includereg52.h #define uchar unsigned char #define uint unsigned int sbit rs=P3^5; sbit en=P3^4; sbit dula=P2^6; sbit wela=P2^7; uchar code tablelcd[]={ 0x30,0x31,0x32,0x33, 0x34,0x35,0x36,0x37, 0x38,0x39,0x41,0x42, 0x43,0x44,0x45,0x46,0x20,0x2d,0x3a,0x27}; uchar table[15]={0x00,0x01,0x02,0x03,0x05,0x06,0x08,0x09,0x0c, 0x43,0x44,0x46,0x47,0x49,0x4a}; uchar num,temp0,n,flag; uint shi,fen,miao,ye,ri,zhou,time,nian; uchar irdate[33]; uchar ircode[4]; uchar disp[8]; uchar xian[8]; uchar xian1[8]; uchar irreceok,irtime,irflag,bitnum; void delay(uchar z) { uchar x,y; for(x=z;x0;x--) for(y=0;y110;y++); } void timer0init() { EA=1; TMOD=0x12; TH0=0x00; TL0=0x00; TH1=(65536-46080)/256; TL1=(65536-46080)%256; ET0=1; TR0=1; ET1=1; TR1=1; } void intinit() { EA=1; IT0=1; EX0=1; } void irdell() { uchar temp,k,j,i; k=1; for(i=0;i4;i++) { for(j=0;j8;j++) { temp=temp1; if(irdate[k]6) { temp=temp|0x80; } k++; } ircode[i]=temp; } } void irwork() { disp[0]=ircode[0]/16; disp[1]=ircode[0]%16; disp[2]=ircode[1]/16; disp[3]=ircode[1]%16; disp[4]=ircode[2]/16; disp[5]=ircode[2]%16; disp[6]=ircode[3]/16; disp[7]=ircode[3]%16; } void write_com(uchar com) { rs=0; P0=com; delay(5); en=1; delay(5); en=0; } void write_date(uchar date) { rs=1; P0=date; delay(5); en=1; delay(5); en=0; } void init() { shi=0; fen=0; miao=0; nian=2012; ye=1; ri=1; zhou=7; n=0; temp0=100; timer0init(); intinit(); dula=0; wela=0; en=0; write_com(0x38); write_com(0x0f); write_com(0x06); delay(15); write_com(0x38); delay(5); write_com(0x38); delay(5); write_com(0x38); write_com(0x38); write_com(0x08); write_com(0x01); write_com(0x06); write_com(0x0f); } void readrece() { if(ircode[1]==0xbf) /*用户码校，可不要，是为了防止错码而产生误操作而设*/ { switch(ircode[3]) { case 0xf3: temp0=0;/*数字0~9的红外码*/ break; case 0xef: temp0=1; break; cas