钢网架结构拼装工艺标准(506-1996)（Standard for assembly of steel grid structures (506-1996)）.docVIP

下载本文档

2
0
约2.82万字
约 26页
2017-09-13 发布于河南
举报
版权申诉

钢网架结构拼装工艺标准(506-1996)（Standard for assembly of steel grid structures (506-1996)）.doc

1、本文档共26页，可阅读全部内容。
2、原创力文档（book118）网站文档一经付费（服务费），不意味着购买了该文档的版权，仅供个人/单位学习、研究之用，不得用于商业用途，未经授权，严禁复制、发行、汇编、翻译或者网络传播等，侵权必究。
3、本站所有内容均由合作方或网友上传，本站不对文档的完整性、权威性及其观点立场正确性做任何保证或承诺！文档内容仅供研究参考，付费前请自行鉴别。如您付费，意味着您自己接受本站规则且自行承担风险，本站不退款、不进行额外附加服务；查看《如何避免下载的几个坑》。如果您已付费下载过本站文档，您可以点击这里二次下载。
4、如文档侵犯商业秘密、侵犯著作权、侵犯人身权等，请点击“版权申诉”（推荐），也可以打举报电话：400-050-0827(电话支持时间：9:00-18:30)。
5、该文档为VIP文档，如果想要下载，成为VIP会员后，下载免费。
6、成为VIP后，下载本文档将扣除1次下载权益。下载后，不支持退款、换文档。如有疑问请联系我们。
7、成为VIP后，您将拥有八大权益，权益包括：VIP文档下载权益、阅读免打扰、文档格式转换、高级专利检索、专属身份标志、高级客服、多端互通、版权登记。
8、VIP文档为合作方或网友上传，每下载1次，网站将根据用户上传文档的质量评分、类型等，对文档贡献者给予高额补贴、流量扶持。如果你也想贡献VIP文档。上传文档

钢网架结构拼装工艺标准(506-1996)（Standard for assembly of steel grid structures (506-1996)）

钢网架结构拼装工艺标准(506-1996)（Standard for assembly of steel grid structures (506-1996)） Range The process standard is applicable to the ground assembly of steel grid, bolted spherical joints, welded ball joints and welded steel plate joints. Construction preparation 2.1 materials: 2.1.1 steel grid assembled steel and connecting materials, high-strength bolts, welding rod and other materials should comply with the design requirements, and should be factory certification. 2.1.2 bolt ball, hollow welding ball, auxiliary welding ball, taper head, sleeve, seal plate, net frame member, welded steel plate node and other semi-finished products shall comply with the design requirements and the corresponding national standards. 2.1.2.1 steel products used in the manufacture of steel structure space trusses must comply with the design specifications and technical specifications and standards for the corresponding materials. Bolt ball is prohibited from overheating, cracks and hidden dangers. The finished ball must be tested for tensile strength of the largest screw hole. The quality requirements and inspection methods of the bolt ball shall conform to the provisions of table 5-14. Allowable deviation of bolt ball and test method table 5-14 The allowable deviation of sub project (mm) inspection method D = 120, +2.0 -1.0 D120 +3.0 -1.5 D = 1201.5 D120 2.5 3 bolt ball screw end and the sphere center distance + 0.20 with vernier caliper, height gauge inspection, measuring mandrel On the same axis two screw D 1200.20 Hole end face parallelism D120 0.30 The angle between the 5 adjacent two screw holes is equal to 30 . The mandrel, the ruler and the index head are checked by the measuring mandrel 0.5%r 6 screw end verticality with the axis of the indicator Note: R is the end radius of the screw hole. 2.1.2.2 assembly of high-strength bolts of steel must comply with design requirements and the corresponding technical standards. High strength bolts for steel grid structures must adopt the nat