有宏指令的数控铣床编程实例(附普通指令程序)（NC milling program with macro instruction (attached general instruction program)）.docVIP

下载本文档

5
0
约4.32千字
约 8页
2017-09-15 发布于河南
举报
版权申诉

有宏指令的数控铣床编程实例(附普通指令程序)（NC milling program with macro instruction (attached general instruction program)）.doc

1、本文档共8页，可阅读全部内容。
2、原创力文档（book118）网站文档一经付费（服务费），不意味着购买了该文档的版权，仅供个人/单位学习、研究之用，不得用于商业用途，未经授权，严禁复制、发行、汇编、翻译或者网络传播等，侵权必究。
3、本站所有内容均由合作方或网友上传，本站不对文档的完整性、权威性及其观点立场正确性做任何保证或承诺！文档内容仅供研究参考，付费前请自行鉴别。如您付费，意味着您自己接受本站规则且自行承担风险，本站不退款、不进行额外附加服务；查看《如何避免下载的几个坑》。如果您已付费下载过本站文档，您可以点击这里二次下载。
4、如文档侵犯商业秘密、侵犯著作权、侵犯人身权等，请点击“版权申诉”（推荐），也可以打举报电话：400-050-0827(电话支持时间：9:00-18:30)。
5、该文档为VIP文档，如果想要下载，成为VIP会员后，下载免费。
6、成为VIP后，下载本文档将扣除1次下载权益。下载后，不支持退款、换文档。如有疑问请联系我们。
7、成为VIP后，您将拥有八大权益，权益包括：VIP文档下载权益、阅读免打扰、文档格式转换、高级专利检索、专属身份标志、高级客服、多端互通、版权登记。
8、VIP文档为合作方或网友上传，每下载1次，网站将根据用户上传文档的质量评分、类型等，对文档贡献者给予高额补贴、流量扶持。如果你也想贡献VIP文档。上传文档

有宏指令的数控铣床编程实例(附普通指令程序)（NC milling program with macro instruction (attached general instruction program)）

有宏指令的数控铣床编程实例(附普通指令程序)（NC milling program with macro instruction (attached general instruction program)） 1. Hu.mpf 2. G54g90g17g64 3. M03s400 4. R1 = 45 5. Ma1:g258rpl = R1 6. L467 7. If R1 = = 315, gotof ma2 8. R1 = R1 + 90 9. Gotob MA1 10. Ma2:g258rpl = R1 11. L568 12. R1 = R1 - 90 13. If R1 45 gotof Ma3 14. Gotob ma2 15. Ma3:g0z100 16. M5 17. G258rpl = 0 18. G0y220 19. M30 L467.spf 1. G0x43.96y116.302 2. G0z5 3. G1z - 8f500 4. G1x43.698y115.339f100 5. G3x17.138y83.156cr = 23 6. G2x18.831y72.425cr = 19 7. G2x-12.537y60.677cr = 19f500 8. G2x-17.137y83.156cr = 19f100 9. G3x-32.818y115.521cr = 23 10. G1x-32.598y116.497f500 11. G0z5 12. RET L568.spf 1. G0z5 2. X-46.523y115.252 3. G01z - 8f500 4. G1z-9.98f100 5. G1x-46.002y113.750 6. G2x-17.978y83.715cr = 22 7. G3x-19.740y71.743cr = 20 8. G1x0y74.953 9. G1x19.752y71.816 10. G3x17.978y83.715cr = 20 11. G2x46.002y113.75cr = 22 12. G1x30.560y122.68f1000 13. G1x0y123.5 14. G01y113.5f100 15. G0z5 16. RET Program description: This program after several changes after the formation, with the tool center programming, machining parts as shown in Figure four circular pits and round. The program has been run by XK714G milling machine, using the SIEMENS 802C system of machine tool. The main program in the fifth sentence, the programming of coordinate rotation of 45 degrees, this is because the initial and we are not familiar with the SIEMENS system, the system is always due to inaccurate data and alarm. (the system requirements data of 3 decimal places, with to test if you use four to five homes, the system will alarm) technical personnel machine vendors to help please. They think I have clamping parts to the direction of machining parts and the machine coordinate direction between the angle, which is not conducive to system calculation, easy system caused by calculation errors in the processing before the alarm, therefore, the first part of the programming of a coordinate rotation The procedure has been changed many times, but th