模具常用术语中英文对照（Common terms for moulds, in English and Chinese）.docVIP

下载本文档

14
0
约7.91千字
约 25页
2017-09-15 发布于河南
举报
版权申诉

模具常用术语中英文对照（Common terms for moulds, in English and Chinese）.doc

1、原创力文档（book118）网站文档一经付费（服务费），不意味着购买了该文档的版权，仅供个人/单位学习、研究之用，不得用于商业用途，未经授权，严禁复制、发行、汇编、翻译或者网络传播等，侵权必究。。
2、本站所有内容均由合作方或网友上传，本站不对文档的完整性、权威性及其观点立场正确性做任何保证或承诺！文档内容仅供研究参考，付费前请自行鉴别。如您付费，意味着您自己接受本站规则且自行承担风险，本站不退款、不进行额外附加服务；查看《如何避免下载的几个坑》。如果您已付费下载过本站文档，您可以点击这里二次下载。
3、如文档侵犯商业秘密、侵犯著作权、侵犯人身权等，请点击“版权申诉”（推荐），也可以打举报电话：400-050-0827(电话支持时间：9:00-18:30)。
4、该文档为VIP文档，如果想要下载，成为VIP会员后，下载免费。
5、成为VIP后，下载本文档将扣除1次下载权益。下载后，不支持退款、换文档。如有疑问请联系我们。
6、成为VIP后，您将拥有八大权益，权益包括：VIP文档下载权益、阅读免打扰、文档格式转换、高级专利检索、专属身份标志、高级客服、多端互通、版权登记。
7、VIP文档为合作方或网友上传，每下载1次，网站将根据用户上传文档的质量评分、类型等，对文档贡献者给予高额补贴、流量扶持。如果你也想贡献VIP文档。上传文档

模具常用术语中英文对照（Common terms for moulds, in English and Chinese）

模具常用术语中英文对照（Common terms for moulds, in English and Chinese） Common terms for moulds, in English and Chinese Chinese English Mold core Parting Core Partial view Partial View Cold # Cold Sllig Line cutting, Wire, E.D.M Contour Contour Threaded hole Tapping, Hole Connector Fittings Oblique needle Angle Pin Bonding Engage Replace inserts Interchangeable, Mold, Inserts Designated tonnage injection molding machine Specific Press Tap joint Water, Fittings Thread Eyebolt Thread Back stitch Stop Pin Two stage ejector pin Sub-Leaderd Pin Insert Mold Insert Hard Hapden Sprue Sprue Design cylinder Design Preliminary Name block table Title Block Version ID Revision Level Bill of materials Stock List Molding Build, Mold Manual slider Hand Slide Leak test Leak Test Runner exhaust Runner Vents Polished Draw Polish Side core pulling Side Action Chinese English Stiffener Reinforcing Bracing Gusset Pillar Bosse Out of mould slope Draft Contour Gallery The single session Kick-Off Meeting Loading holes Handl, Ing, Hole Conveyor belts, Moldstrap Code slot Clamp, Slot Brace up, Support, Pillar Spiral tooth 1/2-13, Eye, Bolt, 1/2-13Tap Guide post Leader, Pin, Location Anti adhesive Teflon Paste Offset Offset Water slug Water, Line, Plig Pry the feet Ppy Slot Reprocess Reworked Accessories Components Compensation Compensation Flatness Parallel Chamfer Chamfer Base Mold Base Hot mouth Hotnozzle Spark machine Edm Welding line Weildline Press Press Texturing rays Trapezoidal Trapezoio Flange and flange Flange Common terms for moulds, in English and Chinese Chinese English Square iron Spacer Block Ejector plate Ejector Plate Ejector plate Ejector, Retainer, Plate Backing plate Retainer Plate Core Pin Rubbish nail Stop Pin There are ejector pins Shoulder, Ejector, Pin Thimble plate guide sleeve Guided, Ejection, Bushing Guide pins Guided, Ejection, Leader, Pin Sprue Sprue Bushing Three mode extended sprue Extension Nozzle Bushing Nozzle plate guide sleeve Runner, Stripper, Plate, Bushing Positi