汽车贴膜的操作步骤与验收（Operation procedure and acceptance of automobile film）.docVIP

下载本文档

4
0
约6.08千字
约 6页
2017-10-16 发布于河南
举报
版权申诉

汽车贴膜的操作步骤与验收（Operation procedure and acceptance of automobile film）.doc

1、原创力文档（book118）网站文档一经付费（服务费），不意味着购买了该文档的版权，仅供个人/单位学习、研究之用，不得用于商业用途，未经授权，严禁复制、发行、汇编、翻译或者网络传播等，侵权必究。。
2、本站所有内容均由合作方或网友上传，本站不对文档的完整性、权威性及其观点立场正确性做任何保证或承诺！文档内容仅供研究参考，付费前请自行鉴别。如您付费，意味着您自己接受本站规则且自行承担风险，本站不退款、不进行额外附加服务；查看《如何避免下载的几个坑》。如果您已付费下载过本站文档，您可以点击这里二次下载。
3、如文档侵犯商业秘密、侵犯著作权、侵犯人身权等，请点击“版权申诉”（推荐），也可以打举报电话：400-050-0827(电话支持时间：9:00-18:30)。
4、该文档为VIP文档，如果想要下载，成为VIP会员后，下载免费。
5、成为VIP后，下载本文档将扣除1次下载权益。下载后，不支持退款、换文档。如有疑问请联系我们。
6、成为VIP后，您将拥有八大权益，权益包括：VIP文档下载权益、阅读免打扰、文档格式转换、高级专利检索、专属身份标志、高级客服、多端互通、版权登记。
7、VIP文档为合作方或网友上传，每下载1次，网站将根据用户上传文档的质量评分、类型等，对文档贡献者给予高额补贴、流量扶持。如果你也想贡献VIP文档。上传文档

汽车贴膜的操作步骤与验收（Operation procedure and acceptance of automobile film）

汽车贴膜的操作步骤与验收（Operation procedure and acceptance of automobile film） Specific operation of car side window foil 1. film extraction Step 1: measure size Measure the size of the glass outside of the glass with a tape measure, mainly in width and height. Note that the amount must be measured at the widest and highest part of the glass, and 1.5 to 3 centimeters should be reserved at both ends as a margin to prevent excessive clipping. The second step: rough cut With a paper knife and a ruler (with best) according to previous measured data, cut out from the window in the rectangular window, cut the film to move, should be rolled into a tube shaped, prevent wrinkles occur in the move. When taking the mold, it is important to note that the glass horizontal width is the direction of the film, which is determined by the shrinkage of the film. The third step: two rough cutting Cut off the obvious excess film to facilitate the cutting work in the back, so that the main part of the film can be avoided. The fourth part: fine cut With a paper knife cut along the edges of the glass film, the edge of the glass can be exposed part of the window, this step is already shaping step: for the edge of the glass can not be exposed part of the window, and after the two step process. First, adjust the position of the edge of the glass film, according to the shape of the knife cutting window; the window is removed, the right move 5 mm and 8 mm respectively, even cut out the right edge of the membrane shape, adjust the window to the best position. The fifth step: scribing Write not cut along the line of combined window glass and frame draw down. When drawing, use a pen to draw off the lower edge and the left edge of the glass and rubber intersecting line. The sixth part: the two cutting The film back plate, with a ruler and a paper cutter according to the marking reserving proper allowance after cut. Generally speaking, the lower edge usually stays about 2-4 centimeters, which needs to be deter