模具维修的15个问题的解决方法（Solutions to 15 problems in die maintenance）.docVIP

下载本文档

3
0
约8.89千字
约 8页
2017-09-26 发布于河南
举报
版权申诉

模具维修的15个问题的解决方法（Solutions to 15 problems in die maintenance）.doc

1、原创力文档（book118）网站文档一经付费（服务费），不意味着购买了该文档的版权，仅供个人/单位学习、研究之用，不得用于商业用途，未经授权，严禁复制、发行、汇编、翻译或者网络传播等，侵权必究。。
2、本站所有内容均由合作方或网友上传，本站不对文档的完整性、权威性及其观点立场正确性做任何保证或承诺！文档内容仅供研究参考，付费前请自行鉴别。如您付费，意味着您自己接受本站规则且自行承担风险，本站不退款、不进行额外附加服务；查看《如何避免下载的几个坑》。如果您已付费下载过本站文档，您可以点击这里二次下载。
3、如文档侵犯商业秘密、侵犯著作权、侵犯人身权等，请点击“版权申诉”（推荐），也可以打举报电话：400-050-0827(电话支持时间：9:00-18:30)。
4、该文档为VIP文档，如果想要下载，成为VIP会员后，下载免费。
5、成为VIP后，下载本文档将扣除1次下载权益。下载后，不支持退款、换文档。如有疑问请联系我们。
6、成为VIP后，您将拥有八大权益，权益包括：VIP文档下载权益、阅读免打扰、文档格式转换、高级专利检索、专属身份标志、高级客服、多端互通、版权登记。
7、VIP文档为合作方或网友上传，每下载1次，网站将根据用户上传文档的质量评分、类型等，对文档贡献者给予高额补贴、流量扶持。如果你也想贡献VIP文档。上传文档

模具维修的15个问题的解决方法（Solutions to 15 problems in die maintenance）

模具维修的15个问题的解决方法（Solutions to 15 problems in die maintenance） The molding block is not smooth, the forming block is electroplated and polished, so as to improve the smoothness of the concave convex die. The bending radius R of the punch is too small to increase the bending radius of the punch The bending clearance of the die is too small to adjust the bending clearance between the upper and lower dies. The die forming block with roller forming. 7. missing punching The leakage of punching, are generally not found, broken punch punch, punch loading caused by factors such as leakage subsidence die repair, repair mode should be carried out after the first confirmed cases, and sample comparison, check whether the omission phenomenon of punch sinking, should improve the hardness of upper die plate. 8., stripping is not normal When the stripper plate is too tight with the punch, the stripper is inclined, the height of the screw is not uniform, or the other stripping device is not proper, the material shall be trimmed and removed, and the stripper screw shall be in the form of a sleeve and an inner six angle screw. The clearance of the die is too small, and the punch needs a great deal of releasing force when it is out of the material, which causes the punch to be bitten by the material and needs to increase the clearance of the lower die. The concave die has an inverted cone, and the die is trimmed. The blanking hole of the concave die and the blanking hole of the lower die seat are not opposite, and the material leakage hole is trimmed. Check the status of processing materials. The material is soiled and attached to the mold, so that the punch is bitten by the material and cannot be machined. After warping, the material will clamp the punch and find that the warp deformation material needs to be smoothed and reprocessed. 6, punch and die cutting edge passivation in grinding. The cutting edge of the mold can make a beautiful cut section, the blade is blunt and requires extr