电源调试经验随笔(Power supply debugging experience).docVIP

电源调试经验随笔(Power supply debugging experience).doc

  1. 1、原创力文档(book118)网站文档一经付费(服务费),不意味着购买了该文档的版权,仅供个人/单位学习、研究之用,不得用于商业用途,未经授权,严禁复制、发行、汇编、翻译或者网络传播等,侵权必究。。
  2. 2、本站所有内容均由合作方或网友上传,本站不对文档的完整性、权威性及其观点立场正确性做任何保证或承诺!文档内容仅供研究参考,付费前请自行鉴别。如您付费,意味着您自己接受本站规则且自行承担风险,本站不退款、不进行额外附加服务;查看《如何避免下载的几个坑》。如果您已付费下载过本站文档,您可以点击 这里二次下载
  3. 3、如文档侵犯商业秘密、侵犯著作权、侵犯人身权等,请点击“版权申诉”(推荐),也可以打举报电话:400-050-0827(电话支持时间:9:00-18:30)。
  4. 4、该文档为VIP文档,如果想要下载,成为VIP会员后,下载免费。
  5. 5、成为VIP后,下载本文档将扣除1次下载权益。下载后,不支持退款、换文档。如有疑问请联系我们
  6. 6、成为VIP后,您将拥有八大权益,权益包括:VIP文档下载权益、阅读免打扰、文档格式转换、高级专利检索、专属身份标志、高级客服、多端互通、版权登记。
  7. 7、VIP文档为合作方或网友上传,每下载1次, 网站将根据用户上传文档的质量评分、类型等,对文档贡献者给予高额补贴、流量扶持。如果你也想贡献VIP文档。上传文档
查看更多
电源调试经验随笔(Power supply debugging experience)

电源调试经验随笔(Power supply debugging experience) Power supply debugging wise remark of an experienced person I think every power to do the people have such a feeling, is a lot of ability is through the experience of training, in line to see a power study notes, arrange to share to you, dont know what you have ever encountered problems. Project 1:UC3842 control circuit learning board Phenomenon: UC3842 power supply is normal, but Vref is not 5V, but higher than 5V. The solution: to weld the pipe again. Analysis: UC3842 GND feet welding poor, resulting in voltage floating up Item 2: a laboratory, a power failure, take a look at, UC3875 control of the entire bridge, need to be repaired. Phenomenon: preliminary check, the power pipe is broken, because there is no model of the pipe, all the pipes into the same power level of the pipe. After power on, when the input voltage is low, everything is normal. When the input voltage is high, the drive is confused and frequency jitter. Solution: the power tube drive resistance increases, the phenomenon disappeared, everything is normal, the power supply fixed. Analysis: the new pipe parasitic parameters are different from those of the old tubes. Under the same driving circuit, the switching speed will be faster, resulting in relatively large interference, and at high voltage, interference will affect the work of the control circuit. Item 3:UC3845 double barreled forward Phenomenon: after two tubes are shut down, the voltage that DS bears is very different, not half of them in theory. The guess is that the parameters of the MOS are inconsistent, causing the upper and lower tubes to be welded down and switched positions, and the result remains the same. Doesnt seem to have anything to do with MOS. Solution: adjust the two pipe drive, so that they try to turn off at the same time, the situation improved slightly, but still can not share the voltage. Analysis: this should be caused by two reasons. One is that the parasitic parameters of t

您可能关注的文档

文档评论(0)

f8r9t5c + 关注
实名认证
文档贡献者

该用户很懒,什么也没介绍

版权声明书
用户编号:8000054077000003

1亿VIP精品文档

相关文档