西交《机械设计基础》在线作业（West turn mechanical design foundation online homework）.doc

下载文档 降价啦

3
0
约1.04万字
约 21页
2017-10-07 发布于河南
举报
版权申诉
保障服务

西交《机械设计基础》在线作业（West turn mechanical design foundation online homework）.doc

1、本文档共21页，可阅读全部内容。
2、原创力文档（book118）网站文档一经付费（服务费），不意味着购买了该文档的版权，仅供个人/单位学习、研究之用，不得用于商业用途，未经授权，严禁复制、发行、汇编、翻译或者网络传播等，侵权必究。
3、本站所有内容均由合作方或网友上传，本站不对文档的完整性、权威性及其观点立场正确性做任何保证或承诺！文档内容仅供研究参考，付费前请自行鉴别。如您付费，意味着您自己接受本站规则且自行承担风险，本站不退款、不进行额外附加服务；查看《如何避免下载的几个坑》。如果您已付费下载过本站文档，您可以点击这里二次下载。
4、如文档侵犯商业秘密、侵犯著作权、侵犯人身权等，请点击“版权申诉”（推荐），也可以打举报电话：400-050-0827(电话支持时间：9:00-18:30)。

西交《机械设计基础》在线作业（West turn mechanical design foundation online homework）

西交《机械设计基础》在线作业（West turn mechanical design foundation online homework） West turn mechanical design foundation online homework Total score: 100 test time: - Radio examination A multiple-choice question Judgment question Radio examination questions (20 questions, 40 points) The number of degrees of freedom in 1. planar mechanisms is at most. A. one B. two C. three D. four Full marks: 2 2., the basic rated life of a ball bearing is 36kN, the basic rated life is 729 thousand rpm, the maximum equivalent dynamic load that the bearing can bear is () kN. A. 30 B. 35 C. 40 D. 45 Full marks: 2 The main form of failure of the 3. pin connection is (). A. shear and crushing B. twist deformation C. bending fracture D. gluing Full marks: 2 The 4. () measures can not improve the rigidity of the shaft. A. uses high strength alloy steel B. changes the supporting position of the shaft C. changes the diameter of the shaft D. is wrong Full marks: 2 5., the freedom of two planar mechanisms is equal to 1, and now they are strung into a planar mechanism by a moving element with two hinges, and the degree of freedom is equal to (). A. 0 B. 1 C. 2 D. 3 Full marks: 2 6. for the closed hard toothed surface gear drive, it is better to take fewer teeth and increase the modulus, the purpose is (). A. to improve the contact strength of tooth surface B. reduces the slip coefficient and improves the transmission efficiency C. ensures the bending strength of the gear teeth D. is wrong Full marks: 2 7. in mechanical transmission, the instantaneous transmission constant is theoretically guaranteed. A. belt drive B. chain drive C. gear drive, #V belt drive Full marks: 2 The failure mode of the 8. worm gear is similar to that of the gear drive, among which the most prone to occur. Pitting corrosion and wear of A. B. bonding and wear Fracture and plastic deformation of C. gear D. is wrong Full marks: 2 9. in worm gear, other conditions are the same. If the number of worm heads is increased, (. The A. tran