三菱gps-3电梯故障代码查询（MITSUBISHI GPS-3 elevator fault code inquiry）.docVIP

下载本文档

43
0
约1.21万字
约 17页
2017-10-05 发布于河南
举报
版权申诉

三菱gps-3电梯故障代码查询（MITSUBISHI GPS-3 elevator fault code inquiry）.doc

1、原创力文档（book118）网站文档一经付费（服务费），不意味着购买了该文档的版权，仅供个人/单位学习、研究之用，不得用于商业用途，未经授权，严禁复制、发行、汇编、翻译或者网络传播等，侵权必究。。
2、本站所有内容均由合作方或网友上传，本站不对文档的完整性、权威性及其观点立场正确性做任何保证或承诺！文档内容仅供研究参考，付费前请自行鉴别。如您付费，意味着您自己接受本站规则且自行承担风险，本站不退款、不进行额外附加服务；查看《如何避免下载的几个坑》。如果您已付费下载过本站文档，您可以点击这里二次下载。
3、如文档侵犯商业秘密、侵犯著作权、侵犯人身权等，请点击“版权申诉”（推荐），也可以打举报电话：400-050-0827(电话支持时间：9:00-18:30)。
4、该文档为VIP文档，如果想要下载，成为VIP会员后，下载免费。
5、成为VIP后，下载本文档将扣除1次下载权益。下载后，不支持退款、换文档。如有疑问请联系我们。
6、成为VIP后，您将拥有八大权益，权益包括：VIP文档下载权益、阅读免打扰、文档格式转换、高级专利检索、专属身份标志、高级客服、多端互通、版权登记。
7、VIP文档为合作方或网友上传，每下载1次，网站将根据用户上传文档的质量评分、类型等，对文档贡献者给予高额补贴、流量扶持。如果你也想贡献VIP文档。上传文档

三菱gps-3电梯故障代码查询（MITSUBISHI GPS-3 elevator fault code inquiry）

三菱gps-3电梯故障代码查询（MITSUBISHI GPS-3 elevator fault code inquiry） MITSUBISHI GPS-3 elevator trouble code query table complete version Time: 2010-06-21 08:56 source: Author: Click: sub font settings: large, medium and small - MITSUBISHI elevator GPS-3 two switch MON1 and MON0 in the room P1 electronic board, as long as the rotation of the two switches to a different location, through the display of letters in the corresponding Chinese, you can figure out the fault position and the elevator failure time and the number of the. Go to the 0 position, and then turn the MON0 switch to the 0 position. The result is as follows: Display results ----E0 no fault SW-TGBL is detected when the ------E1 speed is abnormally low ------E2 is too large to check out SW-TGBH ------E3 reversal is checking out SW-TGBR SW-AST is detected when ------E4AST is abnormal ------E5 inverter detected SS-LOCFO during overcurrent ------E6 rectifier over current detection SS-COVH SS-LVLT is detected when the ------E7 rectifier is low voltage ------E8LB coil fault, power failure detected SW-CFLB ------E95 coil fault, power failure detected SW-CFU ------EA forced contact ON/OFF fault detected SW-CFBK ------EB car direct signal transmission abnormal ST-STSCE ------EC out of office and direct signal transmission exception, ST-STSHE ------ED system exception ST-SYER The ------EE driver is unable to start SD-DNRS ------EF controls cannot start SW-NRS 0. Keep the MON1 unchanged and rotate the MON0 to the 1 position. Shows the position of the car and the balance camel. The balance is between 0-0. The 1 is equal to 256MM, and the 2 is equal to 512MM. Keep the MON1 unchanged and rotate the MON0 to the 2 position. Data input, installation time, and SW1 at the same time Keep the MON1 unchanged and rotate the MON0 to the 3 position. Show floor Keep the MON1 unchanged and rotate the MON0 to the 4 position. Show floor Keep the MON1 unchanged and rotate the MON0 to the 5 position. Weighing data input, maintenance use Kee