- 1、原创力文档(book118)网站文档一经付费(服务费),不意味着购买了该文档的版权,仅供个人/单位学习、研究之用,不得用于商业用途,未经授权,严禁复制、发行、汇编、翻译或者网络传播等,侵权必究。。
- 2、本站所有内容均由合作方或网友上传,本站不对文档的完整性、权威性及其观点立场正确性做任何保证或承诺!文档内容仅供研究参考,付费前请自行鉴别。如您付费,意味着您自己接受本站规则且自行承担风险,本站不退款、不进行额外附加服务;查看《如何避免下载的几个坑》。如果您已付费下载过本站文档,您可以点击 这里二次下载。
- 3、如文档侵犯商业秘密、侵犯著作权、侵犯人身权等,请点击“版权申诉”(推荐),也可以打举报电话:400-050-0827(电话支持时间:9:00-18:30)。
- 4、该文档为VIP文档,如果想要下载,成为VIP会员后,下载免费。
- 5、成为VIP后,下载本文档将扣除1次下载权益。下载后,不支持退款、换文档。如有疑问请联系我们。
- 6、成为VIP后,您将拥有八大权益,权益包括:VIP文档下载权益、阅读免打扰、文档格式转换、高级专利检索、专属身份标志、高级客服、多端互通、版权登记。
- 7、VIP文档为合作方或网友上传,每下载1次, 网站将根据用户上传文档的质量评分、类型等,对文档贡献者给予高额补贴、流量扶持。如果你也想贡献VIP文档。上传文档
查看更多
第二章 冲裁模的结构与设计
一、课题:Task
第二章 冲裁模的结构与设计
Chapter Two Blanking die’s structure and design
二、目的要求:Intention and request
掌握了解冲裁模的冲裁工艺及基本知识。
清楚了解冲裁过程分析并能够掌握冲裁件的质量分析。
掌握冲裁间隙的计算、分析及应用。
三、重点、难点和突破的方法: Important points、difficulty points and breach methods
冲裁工艺。 Blanking technique.
典型冲裁模结构。 Typical blanking die’s constructer.
冲裁模主要零部件的结构分析与标准的选用。The constructer analysis and standards’ selection of blanking die’s important components
.
冲裁模设计要点the important points of blanking die’s design.
四、复习提问:Review and question
模具间隙正常时,金属板料的冲裁变形过程大致可分为哪三个变形阶段?Where has 3 phases the metal sheet matal’s blanking distortion procedure,when the mould gap is normal.
在正常的冲裁工作条件下
,冲裁件断面具有哪四个明显特征区?
Where has four evident earmark zone’s blanking piece’s sever, At the normal conditions of blanking work.
五、教具:Teaching aid
多媒体 multimedia
六、作业:Homework
习题2.1 Exercise 2.1
七、授课讲义:Classroom teaching
第二章 冲裁模的结构与设计
Chapter Two Blanking die’s structure and design
使板料分离的冲压工艺称为冲裁。
The stamping technique to divide the sheet matal is called blanking. There are various kinds of it.such as, cut down, punch,pierce, trim, incise, dissect and so on.
冲裁工艺的种类很多,常用的有切断、落料、冲孔、切边、切口、剖切等。Cut、Blanking、Punch、Cutting edge、Slitting and so on。
冲裁是冲压工艺的最基本工序之一。blanking is one basic procedure of stamping technique。在冲压加工中应用极广。它既可以直接冲出成品零件,也可以作为弯曲、拉深和挤压等其它工序的坯料,还可以在已成形的工件上进行再加工(切边、切口、冲孔等工序)。
2.1 冲裁工艺 Blanking technique.
2.1.1 冲裁基本知识the basic knowledge of Blanking
在冲裁工艺中,以落料、冲孔应用最多。The most use of it is punching and piercing.从板料上冲下所需形状的工件(或毛坯)称为落料。Run into the required type’s work piece from the sheet matal (or roughcast) is punching.在工件上冲出所需形状的孔(冲去的为废料)称为冲孔。Run into the required form’s work piece ( the washed thing is scrap ) is pierce 落料和冲孔的变形性质完全相同,但在进行模具工作部分设计时,要分开加以考虑。Punching and pierce have the same distortion feature , but when doing the model work design , we should distinguish them to consider them
?
根据冲裁变形机理的不同,冲裁工艺可以分为普通冲裁和精密冲裁两大类。According to the different distortion mechanism, blanking technique has two types are common bl
文档评论(0)