梨形头及C型快速卸扣使用说明.doc

C型快速卸扣及梨形绳套 C-type quick Shackle and pear-shaped socket 使用方法及报废标准 usage and scrap standard C型快速卸扣，参照标准：JT/T246-1995 使用条件: C型快速卸扣一般使用于桥式抓斗起重机下钢丝绳端梨型绳套或起重链之间的连接件,它以快速拆卸而广泛应用于抓斗、吊钩、吊具等的快速更换，在与梨形绳套的组合使用中能通过宽槽滑轮，提高起升高度。 C-type quick shackle ,reference standard：JT/T246-1995 Working condition: C-type quick shackles are generally used as connecting fitting between pear-shaped sockets or between pear-shaped socket and lifting chains under the crane. It is widely used for the rapid replacement of grabs, hooks, spreaders ,etc. with its quick disassemble . It can be used with pear-shaped socket by wide groove pulley to raise lifting height. 使用方式如下图： Use as below: C型快速卸扣主要技术参数 Main technical parameters 产品编号 Serial No. 主要尺寸 Dimensions 安全系数 Safety index 适配梨型绳套规格 Specifications of corresponding pear-shaped socket 适配起重链规格 Specifications of corresponding lifting chain d L B C A THLE8#-8t φ27 162 108 35 31 5 8#-φ25-27 φ25 THLE9#-10t φ29 174 116 37 34 5 9#-φ28-30 φ28 THLE10#-12.5t φ32 192 128 41 37 5 10#-φ31-33 φ30 THLE11#-14t φ35 210 140 44 40 5 11#-φ34-36 φ35 THLE12#-16t φ38 228 152 48 43 5 12#-φ37-39 φ37 THLE13#-21t φ41 246 164 51 46 5 13#-φ40-42 φ40 THLE14#-25t φ44 264 176 54 50 5 14#-φ43-45 φ45 THLE15#-32t φ47 282 188 58 52 5 15#-φ46-48 φ50 THLE17#-45t φ55 330 220 66 62 4 17#-φ53-56 φ55 1.3使用注意事项及报废标准 C型快速卸扣在与梨型绳套连接后使用时，表面及连接部分必须每班（8小时）加锂基润滑脂1—2次，加油厚度3mm以上。如产品在使用中，相关尺寸磨损超过15%、变形超过10%时应予以报废，如表面发现裂纹、缺损等应立即予以报废.产品出厂后，最长使用期限为2年。 Precautions for use and scrap standards Lubricate the surface of C-type quick shackle and the junction with pear-shaped socket by lithium based grease lubricant 1 or 2 times each work(8 hours), the thickness of the oil must be over 3mm. The products should be scrapped if the abrasion and distortion for relevant dimension is over 15% and over 10%, and also if you find cracks or damage etc. on the surface. The logest operating period of product is 2 years. C型快速卸扣 型号 Serial No. d 装卸作业次数 Times of operations 适配梨型绳套 规格 Specifications o