Prec工艺流程isionMeasuringPart#.pptxVIP

  1. 1、原创力文档(book118)网站文档一经付费(服务费),不意味着购买了该文档的版权,仅供个人/单位学习、研究之用,不得用于商业用途,未经授权,严禁复制、发行、汇编、翻译或者网络传播等,侵权必究。。
  2. 2、本站所有内容均由合作方或网友上传,本站不对文档的完整性、权威性及其观点立场正确性做任何保证或承诺!文档内容仅供研究参考,付费前请自行鉴别。如您付费,意味着您自己接受本站规则且自行承担风险,本站不退款、不进行额外附加服务;查看《如何避免下载的几个坑》。如果您已付费下载过本站文档,您可以点击 这里二次下载
  3. 3、如文档侵犯商业秘密、侵犯著作权、侵犯人身权等,请点击“版权申诉”(推荐),也可以打举报电话:400-050-0827(电话支持时间:9:00-18:30)。
  4. 4、该文档为VIP文档,如果想要下载,成为VIP会员后,下载免费。
  5. 5、成为VIP后,下载本文档将扣除1次下载权益。下载后,不支持退款、换文档。如有疑问请联系我们
  6. 6、成为VIP后,您将拥有八大权益,权益包括:VIP文档下载权益、阅读免打扰、文档格式转换、高级专利检索、专属身份标志、高级客服、多端互通、版权登记。
  7. 7、VIP文档为合作方或网友上传,每下载1次, 网站将根据用户上传文档的质量评分、类型等,对文档贡献者给予高额补贴、流量扶持。如果你也想贡献VIP文档。上传文档
查看更多
Prec工艺流程isionMeasuringPart#

AUTO1120;;Using a micrometer to measure the connecting rod journal for out-of-round and taper.;;Crankshaft journal measurements. Each journal should be measured in at least six locations, but also in position A and position B and at 120-degree intervals around the journal.;;Taper To determine the taper of the journal, compare readings in the same place between A and B positions and subtract the lower readings from the higher reading. For example:;;Camshaft journals should be measured in three locations, 120 degrees apart, to check for out-of-round.;;Digital Micrometers Some technicians use a digital micrometer, which is easier to read. Because these tools do not have the various scales, the measurement is displayed and read directly off the micrometer.;;TELESCOPIC GUAGE;When the head is first removed, the cylinder taper and out-of-round should be checked below the ridge (a) and above the piston when it is at the bottom of the stroke (b).;(a) A telescopic gauge being used to measure the inside diameter (ID) of a camshaft bearing. (b) An outside micrometer used to measure the telescopic gauge.;;SMALL HOLE GAUGE;;Vernier Caliper A vernier caliper has a movable scale that is parallel to a fixed scale. These precision measuring instruments are capable of measuring outside and inside diameters and most will even measure depth.;The imperial main scale is divided into inches with each inch divided into 10 parts, each equal to 0.100 inch. The area between the 0.100 marks is divided into four. Each of these divisions is equal to 0.025 inches;Measurement readings are taken by combining the main and vernier scales. At all times, only one division line on the main scale will line up with a line on the vernier Scale. This is the basis for accurate measurements.;To get a final measurement, line up the vernier scale line that is exactly aligned with any line on the main scale.;VERNIER DIAL CALIPER;;FEELER GAUGE; A feeler gauge, also called a thickness gauge, is used to measure

文档评论(0)

ipad0a + 关注
实名认证
文档贡献者

该用户很懒,什么也没介绍

1亿VIP精品文档

相关文档