在notebook里使用matlab作图.docx

1安装word 安装matlab2.在matalb的commond窗口输入 notebook –setup 然后按回车3.输入notebook 即可启动word4，输入matlab命令 如 pi 然后选中（单行可以不选中）后 按下 alt+D 组合键，变绿色，如下所示5.再按下 ctrl+Enter键，执行，出现蓝色结果或者图片。如下所示以下介绍几个matlab基本的操作命令，然后重点写了几个绘图命令（绿色为输入，蓝色为输出）pi ans = 3.1416 vpa(pi,100) ans =3.141592653589793238462643383279502884197169399375105820974944592307816406286208998628034825342117068 syms x f;f=@(x)100*(x(2)-x(1)^2)+(1-x(1))^2 f = @(x)100*(x(2)-x(1)^2)+(1-x(1))^2 x=[1 2],f(x) x = 1 2ans = 100 y=[2 1];f(y) ans = -299 x=linspace(0,2*pi,30);y=sin(x);z=cos(x);plot(x,y,r,x,z,go) ezplot(sin(x),[0,5*pi]) ezplot(cos(t)^3,sin(t)^3,[0,2*pi]) ezplot(exp(x)+sin(x*y),[-2,0.5,0,2]) myfun2=@(x) exp(2.*x)+sin(3.*x.^ 2) myfun2 = @(x)exp(2.*x)+sin(3.*x.^2) plot(-1:0.01:2,myfun2(-1:0.01:2)) fplot(myfun2,[-1,2]); fplot(tanh,[-2,2]) sn = @(x) sin(1./x);fplot(sn,[0.01,0.1]) fplot([tanh(x),sin(x),cos(x)],2*pi*[-1 1]) x=logspace(-1,2);loglog(x,exp(x),-s)grid on t=0:pi/50:10*pi;plot3(sin(t),cos(t),t)rotate3d x=-3:0.1:3;y=1:0.1:5;[X,Y]=meshgrid(x,y);Z=(X+Y).^2;surf(X,Y,Z)shading flat x=-3:0.1:3; y=1:0.1:5; [X,Y]=meshgrid(x,y); Z=(X+Y).^2; mesh(X,Y,Z) [X,Y]=meshgrid(-3:.125:3); Z=peaks(X,Y); meshz(X,Y,Z) x=linspace(0,2*pi,30); y=sin(x); plot(x,y) xlabel(自变量X) ylabel(函数Y) title(示意图) grid on x=linspace(0,2*pi,30); y=sin(x); z=cos(x); plot(x,y,x,z) gtext(sin(x));gtext(cos(x)) x=linspace(0,2*pi,30); y=sin(x); z=cos(x); plot(x,z,:) hold on plot(x,y) x=linspace(0,2*pi,100); y=sin(x);z=cos(x); plot(x,y);title(sin(x)) figure(2); plot(x,z); title(cos(x)); x=linspace(0,2*pi,100); y=sin(x); z=cos(x); a=sin(x).*cos(x);b=sin(x)./(cos(x)+eps); subplot(2,2,1);plot(x,y),title(sin(x)) subplot(2,2,2);plot(x,z),title(cos(x)) subplot(2,2,3);plot(x,a),title(sin(x)cos(x)) subplot(2,2,4);plot(x,b),title(sin(x)/cos(x)) clear;clc;clf;x=linspace(0,2*pi,30); y=sin(x); plot(x,y) zoom on x=-3:0.1:3; y=1:0.1:5; [X,Y]=meshgrid(x,y); Z=(X+Y).^2; subplot(2,2,1), mesh(X,Y,Z),