ANSYS建模命令.docVIP

ANSYS建模命令 /PREP7 ET,1,BEAM4 ET,2,SHELL63 R,1,0.25,0.0052,0.0052,0.5,0.5 R,2,0.2025,0.0034,0.0034,0.45,0.45 R,3,0.06,0.0002,0.00045,0.3,0.2 R,4,0.25,0.25,0.25,0.25 R,5,0.1,0.1,0.1,0.1 MP,EX,1,3.0E10 MP,NUXY,1,0.2 MP,DENS,1,2500 !!!!!!!!!!!!!!!!!!!!!!!!!!!第一层点 *DO,I,1,1 K,1+(I-1)*100,0,0,(I-1)*6 K,2+(I-1)*100,6,0,(I-1)*6 K,3+(I-1)*100,12,0,(I-1)*6 K,4+(I-1)*100,17,0,(I-1)*6 K,5+(I-1)*100,22,0,(I-1)*6 K,6+(I-1)*100,0,5,(I-1)*6 K,7+(I-1)*100,6,5,(I-1)*6 K,8+(I-1)*100,12,5,(I-1)*6 K,9+(I-1)*100,17,5,(I-1)*6 K,10+(I-1)*100,22,5,(I-1)*6 K,11+(I-1)*100,0,10,(I-1)*6 K,12+(I-1)*100,6,10,(I-1)*6 K,13+(I-1)*100,12,10,(I-1)*6 K,14+(I-1)*100,17,10,(I-1)*6 K,15+(I-1)*100,22,10,(I-1)*6 K,16+(I-1)*100,0,15,(I-1)*6 K,17+(I-1)*100,6,15,(I-1)*6 K,18+(I-1)*100,12,15,(I-1)*6 K,19+(I-1)*100,17,15,(I-1)*6 K,20+(I-1)*100,22,15,(I-1)*6 K,21+(I-1)*100,6,1.875,(I-1)*6 K,22+(I-1)*100,6,3.125,(I-1)*6 K,23+(I-1)*100,6,1.875,3.9 K,24+(I-1)*100,6,3.125,3.9 *ENDDO !!!!!!!!!!!!!!!!!!!!!!!!!!! *DO,I,1,19 K,1+I*100,0,0,(I-1)*3+6 K,2+I*100,6,0,(I-1)*3+6 K,3+I*100,12,0,(I-1)*3+6 K,4+I*100,17,0,(I-1)*3+6 K,5+I*100,22,0,(I-1)*3+6 K,6+I*100,0,5,(I-1)*3+6 K,7+I*100,6,5,(I-1)*3+6 K,8+I*100,12,5,(I-1)*3+6 K,9+I*100,17,5,(I-1)*3+6 K,10+I*100,22,5,(I-1)*3+6 K,11+I*100,0,10,(I-1)*3+6 K,12+I*100,6,10,(I-1)*3+6 K,13+I*100,12,10,(I-1)*3+6 K,14+I*100,17,10,(I-1)*3+6 K,15+I*100,22,10,(I-1)*3+6 K,16+I*100,0,15,(I-1)*3+6 K,17+I*100,6,15,(I-1)*3+6 K,18+I*100,12,15,(I-1)*3+6 K,19+I*100,17,15,(I-1)*3+6 K,20+I*100,22,15,(I-1)*3+6 K,21+I*100,6,1.875,(I-1)*3+6 K,22+I*100,6,3.125,(I-1)*3+6 K,23+I*100,6,1.875,(I-1)*3+6+2 K,24+I*100,6,3.125,(I-1)*3+6+2 K,25+I*100,0,1.875,(I-1)*3+6 K,26+I*100,0,3.125,(I-1)*3+6 K,27+I*100,0,1.875,(I-1)*3+6+1.5 K,28+I*100,0,3.125,(I-1)*3+6+1.5 *ENDDO *DO,I,20,20 K,1+I*100,0,0,(I-1)*3+6 K,2+I*100,6,0,(I-1)*3+6 K,3+I*100,12,0,(I-1)*3+6