ansys面映射网格.docVIP

ansys面映射网格 finish /clear /prep7 et,1,plane82 k,1,5 k,2,10 k,3,11,6 k,4,6,15 k,5,-1,8 k,6,,4 l,1,2 l,2,3 l,3,4 larc,4,5,3,10 l,5,6 l,6,1 al,all esize,,3 mshape,0 amap,1,2,5,3,4 与用amesh划分的结果不同 finish /clear /prep7 et,1,42 k,1 k,2,10,-1 k,3,8,6 k,4,1,3 a,1,2,3,4 lesize,1,,,8 lesize,3,,,3 lesize,4,,,7 lesize,2,,,2 将所编号的线划分多少份 mshape,0,2d “0”四边形或六面体 “1”三角形或四面体 2d为二维 3d为三维 mshkey,1 “0”自由网格 “1”映射网格 “2”自由网格和映射网格混合 amesh,all finish /clear /prep7 et,1,42 k,1 k,2,10,-1 k,3,8,6 k,4,1,3 a,1,2,3,4 lesize,1,,,10,0.5 lesize,2,,,10,5 mshape,0,2d mshkey,1 amesh,all esize,1,11 esize,3,3 esize,4,2 esize,2,2 第一个参数控制要画单元的大小 第二个控制要画单元分的分数（两个同时存在时第一个优先） kesize,1,0.2 lesize,1,,,,0.5 mshape,0,2d mshkey,1 amesh,all finish /clear /prep7 et,1,42 k,1 k,2,10,-1 k,3,8,6 k,4,1,3 a,1,2,3,4 lesize,1,,,8 lesize,3,,,3 lesize,4,,,7 lesize,2,,,2 mshape,0,2d mshkey,1 amesh,all 当不满足映射网格划分的条件时，就只能用自由网格划分了 finish /clear /prep7 et,1,95 blc4,,,8,8,8 lesize,all,,,4 lesize,7,,,12 mshape,0,3d mshkey,1 vmesh,all 这是我在simwe论坛里看到的，不过对我这个模型帮助不大，我是用ug建模的，圆柱面，用下面的方法不知道怎么划分。 年轮 finish /clear /prep7 et,1,63 CYL4, , ,1,10, , lsel,s,,,1 lesize,all,,,1 alls amesh,all csys,1 AGEN,36,all, , , ,10, , ,0 NUMMRG,ALL,1e-6, , ,LOW eplot 钱币 finish /clear /prep7 et,1,63 PCIRC,1, ,45,135, RECTNG,-0.3,0.3,-0.3,0.3, aovlap,all asel,s,,,5 adele,all,,,1 alls asel,s,,,4 MSHKEY,1 amesh,all alls csys,1 AGEN,4,all, , , ,90, , ,0 NUMMRG,ALL,1e-6, , ,LOW asel,s,,,1,7,2 aadd,all asel,s,,,9 amesh,all alls eplot 扇面映射 finish /clear /prep7 et,1,63 CYL4, , ,1,90, , lesize,all,,,10 mshkey,1 amesh,all csys,1 AGEN,4,all, , , ,90, , ,0 NUMMRG,ALL,1e-6, , ,LOW eplot 黄金分割 finish /clear /prep7 et,1,63 CYL4, , ,1,90, , lsel,s,,,2,3 lesize,all,,,20 lsel,s,,,1 lesize,all,,,32 alls amesh,all csys,1 AGEN,4,all, , , ,90, , ,0 NUMMRG,ALL,1e-6, , ,LOW eplot 这一种，呵呵，只是随便试着玩搞出来的，没什么实用价值 finish /clear /prep7 et,1,63 CYL4, , ,1,30, , lsel,s,,,1 lesize,all,,,4 alls MSHKEY,1 amesh,all csys,1 AGEN,12,all, , , ,30, , ,0 NUMMRG,AL