c51 数码管时钟.docVIP

c51 数码管时钟 //S2键调整小时，S3键调整分钟 #include reg51.h #include intrins.h unsigned char data dis_digit; unsigned char key_s, key_v; unsigned char code table[]={0x3f,0x06,0x5b,0x4f,0x66,0x6d,0x7d, 0x07,0x7f,0x6f,0x77,0x7c,0x39,0x5e,0x79,0x71}; unsigned char data dis_buf[8]; unsigned char data dis_index; unsigned char hour,min,sec; unsigned char sec100; sbit K1 = P3^4; sbit K2 = P3^5; sbit dula=P2^6; sbit wela=P2^7; bit scan_key(); void proc_key(); void inc_sec(); void inc_min(); void inc_hour(); //void display(); void delay(unsigned char ms); void display1(unsigned char a1,unsigned char a2,unsigned char a3,unsigned char a4,unsigned char a5,unsigned char a6); void main(void) { P0 = 0xff; P2 = 0xff; TMOD = 0x11; // 定时器0, 1工作模式1, 16位定时方式 TH1 = 0xdc; TL1 = 0; TH0 = 0xFC; TL0 = 0x17; hour = 12; min = 00; sec = 00; sec100 = 0; dis_buf[0] = hour / 10; // 时十位 dis_buf[1] = hour % 10; // 时个位 dis_buf[3] = min / 10; // 分十位 dis_buf[4] = min % 10; // 分个位 dis_buf[6] = sec / 10; // 秒十位 dis_buf[7] = sec % 10; // 秒个位 // dis_buf[2] = 0xbf; // 显示- // dis_buf[5] = 0xbf; // 显示- dis_digit = 0xfe; dis_index = 0; TCON = 0x01; IE = 0x8a; // 使能timer0,1 中断 TR1 = 1; key_v = 0x03; while(1) { if(scan_key()) { delay(10); if(scan_key()) { key_v = key_s; proc_key(); } } display1(dis_buf[0],dis_buf[1],dis_buf[3],dis_buf[4],dis_buf[6],dis_buf[7]); } } bit scan_key() { key_s = 0x00; key_s |= K2; key_s = 1; key_s |= K1; return(key_s ^ key_v); } void proc_key() { EA = 0; if((key_v 0x01) == 0) // K1 { inc_hour(); } else if((key_v 0x02) == 0) // K2 { min++; if(min 59) { min = 0; } dis_buf[3] = min / 10; // 分十位 dis_buf[4] = min % 10; // 分个位 } EA = 1; } /* void timer0() interrupt 1 // 定时器0中断服务程序, 用于数码管的动态扫描 // dis_index --- 显示索引, 用于标识当前显示的数码管和缓冲区的偏移量 // dis_digit --- 位选通值, 传送到P2口用于选通当前数码管的数值, 如等于0xfe时, // 选通P2.0口数码管 // dis_buf --- 显于缓冲区基地址 { TH0 = 0xFC; TL0 = 0