组件过程及最终检验标准.docxVIP

一、过程检验标准1.芯片检验标准芯片级别检验标准A级转换效率≥14%(单晶）或13.5%（多晶）；正面无挂浆；无裂纹；细棚线断线≤0.5mm不超过3条且不连续分布；缺角和崩口≤0.5mm2不超过3个；层压后无明显色差；无逆电流；2.玻璃检验标准玻璃级别检验标准A级透光率≥95%，气泡线度≤2mm不超过3个，极浅划伤 L≤10mm不超过3条；崩边向中间延伸≤1mm不超过3个；平整度≤5%3.铝合金检验标准铝合金级别检验标准A级铝合金标号6063T5；表面氧化均匀，氧化膜层厚度≥10um；表面无划伤、无鼓包；两端高、宽、厚等线度尺寸相差≤0.3mm4.涂锡带检验标准尺寸公差≤±0.01mm，涂锡层均匀，易于焊接，抗拉强度好，不易断裂。5.接线盒检验标准密封、防水，能与硅橡胶牢固粘合，耐老化，绝缘，具有旁路二极管，二极管具有足够的反向耐压和较低正向漏电流，二极管具有高低温的耐温性，整个线路具有较低的电阻，盒体具有足够的散热空间，插头具有好的耐疲劳性二、最终检验标准技术级别功率范围外形尺寸正面外观边框外观背面外观A级≤±3%公差≤1.0mm两端尺寸相差≤0.5mm芯片无挂浆，边缘裂纹≤5mm不超过1条，细栅线断线≤0.5mm不超过3条且不连续分布，缺角和崩口≤0.5mm2不超过3个，表面无明显色差；玻璃极浅划伤L≤10mm不超过3条；组件气泡≤3mm2不超过3个；芯片间距离不小于1mm，芯片与边框间距离不小于8mm表面氧化均匀，表面无划伤、无鼓包；两端线度尺寸相差≤0.3mmTPT无皱痕，表面干净，拱起点高度≤0.2mm;硅胶均匀；接线盒粘接牢固，表面干净三、相应规格电气性能参数125*125 MONO 180WpSpecifications Data Max. Power180WpCell TypeMono-Crystalline Silicon Sorlar CellNo.Of Cells 72 seriesMax.System Voltage1000VDCPower Tolerance±3%Surface Maximum Load Capacity60m/s(200kg/sq.m)Weight15.5kgDimemsions1580×808×35mmElectrical CharaceteristicOpen Circuil Voltage(V) 44.4Short CircuilCurrenl(A)5.40Max.Power Voltage(V)35.6Max.power Current(A)5.05Temperature Coefficienls of Isc(%)+0.017%℃Temperature Coefficienls of Voc(%)-0.34%℃Temperature Coefficienls of Pm(%)-0.48%℃Operating Temperralure-40 to + 85℃Conditions:(STC):Irradiance:1000W/m2, spectral distribution AM1.5, Cell temperature:25℃Features and BenefitsHigh efficicncy solar cells Nominal 24V DC for standard outputCells are Iaminated with EVA, TPT and tempered glass ensuring long life and the most stringent safety requirements for high-voltage operation.Anodized aluminum frame with convenience mounting slotsWithstand hing wind pressure and snow loadOutstanding low-light performancePreeminent aesthetic appearanceEasy installationOutput power tolerance of ±3%25 year limited warranty on power output, 2 year limited warranty on materials and workmanship156*156100WpSpecifications Data Max. Power100WpCell TypeMono-Crystalline Silicon Sorlar CellNo.Of Cells36 seriesMax.System Voltage1000VDCPower Tolerance±3%S