钢筋混凝土钢筋混凝土整体式单向板肋形楼盖设计.docVIP

钢筋混凝土结构课程设计 说 明 书 题目：钢筋混凝土整体式单向板肋形楼盖设计 基础工程一班 谢世瀚 指导老师：王绵坤 广东水利电力职业技术学院市政工程系 2013年1月编制 目录 题目············································3 板的设计······································3 ⑴荷载计算····································3 ⑵计算简图····································3 ⑶弯矩计算····································4 ⑷配筋计算····································5 次梁设计······································5 ⑴荷载计算····································6 ⑵计算简图····································6 ⑶内力计算····································7 ⑷配筋计算····································7 3.主梁设计······································9 ⑴荷载计算····································9 ⑵计算简图····································9 ⑶内力计算····································10 ⑷内力包络图··································13 ⑸配筋计算····································13 4.课程设计总结··································15 参考文献········································17 附图1 附图2 钢筋混凝土课程设计 题目： 某多层仓库平面如图11.48所示，采用现浇钢筋混凝土肋形楼盖，楼面活荷载标准值为8KN/m2,楼面面层为20mm水泥砂浆抹面，天棚抹灰为15mm混合砂浆，混凝土为C35（fc=16.7N/mm2, ft=1.57N/ mm2））））））Φ10@170 As=257 Φ12@200 As=565 564 Φ10@170 As=257 Φ12@200 As=565 372 (293) Φ10@170 As=257 Φ10@200 As=322 429 (625) Φ10@170 As=257 Φ10@200 As=322 注：括号内数据为中间板带的数据 图11.21c 图11.21d 2.次梁的设计 主梁截面高度h=(1/14～1/8)×7200=(900～415)mm,取h=750mm,主梁宽度取250mm。次梁的几何尺寸及支撑情况见图11.21c。 ⑴荷载计算 板传来的恒载 2.66KN/m3×2.4m=6.38KN/m 次梁自重 25KN/m3×0.2m×(0.5-0.08)m=2.1KN/m 次梁粉刷 17KN/m3×0.015m×(0.5-0.08)m×2=0.21KN/m 恒荷载 8.69KN/m 活荷载 8KN/m2×2.4m=19.2KN/m 总荷载设计值 q=(1.2×8.69+1.3×19.2KN/m)=35.39KN/m ⑵计算简图 次梁按考虑塑性内力重分布方法计算内力，计算跨度： 中间跨 l0=ln=7200mm-250mm=6950mm 边跨lo=ln+a/2=(7200-250mm/2-120mm)+120/2=7015mm 1.025ln=7129mm 故取l0=7015mm。 边跨与中间跨的计算跨度相差（7015mm-6950mm） 0.019 0.10.280.35 0.013 0.191 As=α1§bh02fc/fy 1127 1434 771 978 实配钢筋/mm2 3Φ22 (1140) 3Φ25 (1473) 4Φ16 (804)