单片机设计电子密码锁毕业论文推荐.docxVIP

设计题目：电子密码锁功能实现：八位密码锁具有设置密码，然后输入密码验证的功能：设置密码成功后会点亮LED灯提示；录放音模块；输入密码错误则有语音提示；输错3次后LED灯闪烁提示，输错5次以上就禁止输入，且LED灯闪的频率加快；输入正确后播放音乐提示；设置密码和输入密码时不小心按错可以使用清除键；密码破解后可以选择重置密码或继续使用原密码；实现方法：状态机设置密码----输入密码----判断密码是否正确----错误继续回到输入密码状态-----正确则选择是回到输入密码状态或者重置密码设计源程序：#include mega16.hflash unsigned char led_7[13]={0x3F,0x06,0x5B,0x4F,0x66,0x6D, 0x7D,0x07,0x7F,0x6F,0x77,0x7C,0x40}; // 字型码，后3位为“A”，“b”，“-”flash unsigned char position[8]={0x7f,0xbf,0xdf,0xef,0xf7,0xfb,0xfd,0xfe};unsigned char dis_buff[8]; // 显示缓冲区，存放要显示的8个字符的段码值unsigned char key_disbuff[8]; unsigned char key_stime_counter,key_stime_ok1,sign;unsigned char posit;bit key_stime_ok;unsigned char count=0;flash unsigned int t[9]={0,956,865,759,716,638,568,506,470};flash unsigned char d[9]={0,105,116,132,140,157,176,198,209};#define Max_note 32flash unsigned char music[Max_note]= {1,2,1,2,1,2,3,2,5,2,5,2,5,4,5,2,6,2,6,2,6,2,8,2,5,4};unsigned char note_n;unsigned intint_n;bit play_on;interrupt [TIM1_COMPA]void timer1_compa_isr(void) //音乐播放中断{if (!play_on){note_n=0;int_n=1;play_on=1;}else{if (--int_n==0){TCCR1B=0x08;if(note_nMax_note){OCR1A=t[music[note_n]];int_n=d[music[note_n]];note_n++;int_n= int_n * music[note_n];note_n++;TCCR1B=0x09;}elseplay_on=0;}}}void display (void) // 8位LED数码管动态扫描函数{ PORTC = 0xff; PORTA = led_7[dis_buff[posit]]; PORTC = position[posit]; if (++posit =8 ) posit = 0;}#define No_key255#define K1_1 1#define K1_2 2#define K1_3 3#define K2_1 4#define K2_2 5#define K2_3 6#define K3_1 7#define K3_2 8#define K3_3 9#define K4_1 10#define K4_2 0#define K4_3 11#define Key_mask 0bunsigned char read_keyboard() //键盘输入子程序{ static unsigned char key_state = 0, key_value, key_line; unsigned char key_return = No_key,i; switch (key_state){ case 0:key_line = 0b; for (i=1; i=4; i++) // 扫描键盘 { PORTB = ~key_line; // 输出行线电平 PORTB = ~key_line; // 必须送2次！！！（注1）key_value = Key_mask PINB;