丰田5A-FE8A-FE发动机机械部分维修手册.PDF

丰田5A-FE ／8A-FE 发动机机械部分维修手册 目录： 一．部分发动机总成····················································2 （一）组件························································2 （二）大修························································5 二．气缸盖总成·······················································50 （一）组件·······················································50 （二）大修·······················································51 三．气缸体总成·······················································74 （一）组件·······················································74 （二）大修·······················································75 一．部分发动机总成(5A - FE/8A - FE) （一）组件 （二）大修 1．拆下火花塞 2．拆下通风阀分总成 (a) 拆下通风阀。 (b) 拆下垫片。 3． 拆下气门室盖分总成 (a) 拆下加油盖。 (b) 拆下4 个螺母，4 个密封垫和气门室盖。 4． 拆下2 号正时链条或皮带罩 (a) 拆下4 个螺栓和2 号正时皮带罩。 5． 拆下曲轴齿轮或皮带轮罩分总成。 (a) 拆下2 个螺栓和曲轴齿轮罩。 6． 将1 号气缸设定在上止点，压缩位置 (a) 转动曲轴皮带轮，将皮带轮槽口对准1 号正时皮带罩上的正时标记“O”。 (b) 检查曲轴正时皮带轮的“K”标记与轴承盖的正时标记对准。 否则， 转动曲轴一周(3600)。 7． 拆下凸轮轴皮带轮 (a) 使用SST 拆下皮带轮螺栓。 SST 09213 - 54015, 09330 - 00021 (90105 - 08076) (b) 使用SST 拆下曲轴皮带轮。 SST 09950 - 50013 (09951 - 05010, 09952 - 05010 09953 - 05020, 09954 - 05021) 8． 拆下正时链条或皮带罩分总成 (a) 拆下3 个螺栓和正时皮带罩。 9．拆下正时皮带导轮 10.拆下惰轮张紧弹簧 (a) 旋松惰轮安装螺栓。 (b) 拆下张紧弹簧。 11.拆下正时皮带 提示： 如果重复使用正时皮带，在皮带上画一个方向箭头f 按发动机旋转的方向），并 如图所示在皮带轮和皮带上做出定位标记。 (a) 拆下正时皮带。 12.拆下1 号正时皮带惰轮分总成。 (a) 拆下螺栓和l 号正时皮带惰轮。 13.拆下横置发动机安装支架 (a) 拆下3 个螺栓和发动机右侧安装支架。 14. 拆下曲轴正时皮带轮 (a) 如果不能用手拆下皮带轮，使用2 个起子。 注意： 按图示垫上抹布防止损坏。