KSB压力密封设计特稿闸阀的安装和操作时的注意事项.doc

KSB压力自密封ZTS闸阀的安装和操作的注意事项1，工作条件和过热当闸阀处于打开位置时，流体将通过腔B流入阀体内.当阀门被安装在管道，关闭的阀闸阀内将被分割3部分，即在空腔A空腔B和空腔C的流体，如附图中所示。介质现在是环境（冷相）。，空腔B中的压力和温度将迅速上升。闸阀仍然关闭腔A中介质的温度会，压力会几何级数增长。因此，A腔压力到一个不可接受的范围影响到阀楔（参见360部分）。在这种情况下，闸阀打开困难的，这是阀体安全阀应安装在图上所示的位置（部件号：131 0.2）原因释放腔A的2，解决方案A腔压力过大造成困难，建议完成后阀门手轮稍微调整阀门位置阀门顺利。阀门打开无泄漏，请在这个位置复位电动执行机构限位开关，阀下一次电动的位置。以下是设置步骤：使用电动执行器，关闭闸阀位置。使用执行器的手轮打开闸阀，提升2-3毫米复位电动执行器位置限位开关。注意：这种方式关闭闸阀因为执行器的限位开关过矩进一步紧阀门在此条件下阀门将无泄漏。3，安装安全阀建议水压试验完成后前，应安装安全阀。如果或现场工程师一些物质可能会留在阀体管道。这将管道阻塞或安全阀损坏。阀体安全阀安装方法见如下：附录L：阀体安全阀是KSB高性能闸阀一个标准配件。它的功能防止阀腔介质由于汽化，因此，它可以避免阀体和密封面造成的损害。安全阀通常被放置在阀体或阀的旁通管的平台。请参阅所附的目录指定的参数。一压力密封阀盖的上侧。它连接安全阀和前避免杂质或物质进入阀在运输和安装。安装前用户应切断，并管（第710号部分，材质：12CrlMoVG;外径：22x4，ID：14毫米）。安全阀焊接在管的端部，并保持垂直。安全阀的排汽口.且应接到附近的管道，。无论是在水平安装垂直确保安全阀排气口，以避免伤害事故。 Cautions on Installation and operation of KSB Pressure Sealed Design ZTS Gate Valve 1、Working conditions and reasons of over heating troubles When gate valve is in opening position, the fluid will flow into the valve body through cavity B. When the valve is installed on the pipeline and the water testing is completed, upon closing of the valve. the medium remains inside of the Gate valve will be split int0 3 parts, i.e. the fluids in cavity A. cavity B and cavity C as shown in the drawing. The medium is now at the ambient (cold phase). Upon starting of the power unit, pressure and temperature in cavity B will increase rapidly. At this time,the gate valve is still closed and the medium temperature in cavity A will be heated up and the pressure will increase with a geometric growth. ThuS the pressure in cavity A is getting to a very high and unacceptable range effecting onto valve wedge dise (refer to part no. 360 in the drawing). In this case the gate valve may be in the risk and difficult to be opened, this is the reason why a body safety valve should be installed at the position indicated on the drawing (part no. 131 .2) to release the over pressure in cavity A. 2、solutions In consideration of excessive pressure in cavity A. which causing th