项目实验报告-交换和热备一拓扑图和IP规划.docVIP

项目实验报?告----交换和热备? 一拓扑图和?IP规划 二各设备配?置命令 路由器配置?命令 EN CONF T HOSTN?AME BJ-R-1 IP ROUTI?NG INT E0/1 IP ADD 52 NO SHUT EXIT INT E0/2 IP ADD 52 NO SHUT EXIT 第一台三层?交换机的配?置命令 设置接口I?P(IOS需用?unzip?-c3640?-js-mz.124-10,IOS c3640?-is-mz.123-13a不支?持三层功能?) EN CONF T HOSTN?AME BJ-RS-1 IP ROUTI?NG INT F0/15 NO SWITC?HPORT? IP ADD 52 NO SHUT EXIT EXIT 设置VTP?和添加VL?AN VLAN DATAB?ASE VTP DOMAI?N YHL VTP SERVE?R VTP PASSW?ORD 321 VTP PRUNI?NG VTP V2 VLAN 2 NAME SALES? VLAN 3 NAME ENGIN? EXIT 为VLAN?配置IP CONF T INT VLAN 1 IP ADD 1 NO SHUT EXIT INT VLAN 2 IP ADD 1 NO SHUT EXIT INT VLAN 3 IP ADD 1 NO SHUT EXIT 配置中继接?口 INT F0/1 SWITC?HPORT? MODE TRUNK? NO SHUT INT F0/2 SWITC?HPORT? MODE TRUNK? NO SHUT INT F0/13 SWITC?HPORT? MODE TRUNK? NO SHUT INT F0/14 SWITC?HPORT? MODE TRUNK? NO SHUT EXIT 配置以太网?通道 INT RANGE? F0/13 - 14 CHANN?EL-GROUP? 1 MODE ON 将VLAN?1加入热备?组1 INT VLAN 1 STAND?BY 1 IP NO SHUT 将VLAN?2加入热备?组2 INT VLAN2? STAND?BY 2 IP NO SHUT 将VLAN?3加入热备?组3 INT VLAN 3 STAND?BY 3 IP NO SHUT 设置VLA?N1和VL?AN3分别?为热备组1?和3的活跃?路由器 INT VLAN 1 STAND?BY 1 PRIOR?ITY 105 EXIT INT VLAN 3 STAND?BY 3 PRIOR?ITY 105 EXIT 设置VLA?N2为热备?组2的备份?路由器（不用配置，优先级默认?为100，只需将BJ?-RS-2的VLA?N2分别设?置为热备组?2的活跃路?由器就行了?） 设置VLA?N1有热备?组1和3的?占先权 INT VLAN 1 STAND?BY 1 PREEM?PT INT VLAN 3 STAND?BY 3 PREEM?PT 设置热备组?1和3的端?口跟踪 INT VLAN 1 STAND?BY 1 TRACK? F0/15 10 EXIT INT VLAN 3 STAND?BY 3 TRACK? F0/15 10 关闭端口重?定向 INT VLAN 1 NO IP REDIR?ECTS EXIT INT VLAN 2 NO IP REDIR?ECTS EXIT INT VLAN 3 NO IP REDIR?ECTS EXIT 第二台三层?交换机的配?置命令 设置接口I?P EN CONF T HOSTN?AME BJ-RS-2 IP ROUTI?NG INT F0/15 NO SWITC?HPORT? IP ADD 52 NO SHUT EXIT EXIT 设置VTP?和添加VL?AN VLAN DATAB?ASE VTP DOMAI?N YHL VTP SERVE?R VTP PASSW?ORD 321 VTP PRUNI?NG VTP V2 VLAN 2 NAME SALES? VLAN 3 NAME ENGIN? EXIT 为VLAN?配置IP CONF T INT VLAN 1 IP ADD 2 NO SHUT EXIT INT VLAN 2 IP ADD 2 NO SHUT EXIT INT VLAN 3 IP ADD 2 NO SHUT EXIT 配置中继接?口 INT F0/1 SWITC?HPORT? MODE TRUNK? NO SHUT INT F0/2 SWITC?HPORT? MODE TRUNK? NO SHUT INT F0/13 SWITC?HPORT? MODE TRUNK? NO SHUT INT F0/14 S