- 1、本文档共12页,可阅读全部内容。
- 2、原创力文档(book118)网站文档一经付费(服务费),不意味着购买了该文档的版权,仅供个人/单位学习、研究之用,不得用于商业用途,未经授权,严禁复制、发行、汇编、翻译或者网络传播等,侵权必究。
- 3、本站所有内容均由合作方或网友上传,本站不对文档的完整性、权威性及其观点立场正确性做任何保证或承诺!文档内容仅供研究参考,付费前请自行鉴别。如您付费,意味着您自己接受本站规则且自行承担风险,本站不退款、不进行额外附加服务;查看《如何避免下载的几个坑》。如果您已付费下载过本站文档,您可以点击 这里二次下载。
- 4、如文档侵犯商业秘密、侵犯著作权、侵犯人身权等,请点击“版权申诉”(推荐),也可以打举报电话:400-050-0827(电话支持时间:9:00-18:30)。
查看更多
AT89C51的介绍毕业文外文翻译
原文:The Introduction of AT89C51DescriptionThe AT89C51 is a low-power, high-performance CMOS 8-bit microcomputer with 4K bytes of Flash programmable and erasable read only memory (PEROM). The device is manufactured using Atmels high-density nonvolatile memory technology and is compatible with the industry-standard MCS-51 instruction set. The on-chip Flash allows the program memory to be reprogrammed in-system or by a conventional nonvolatile memory programmer. By combining a versatile 8-bit CPU with Flash on a monolithic chip, the Atmel AT89C51 is a powerful microcomputer which provides a highly-flexible and cost-effective solution to many embedded control applications.Function characteristicThe AT89C51 provides the following standard features: 4K bytes of Flash, 128 bytes of RAM, 32 I/O lines, two 16-bit timer/counters, one 5 vector two-level interrupt architecture, a full duplex serial port, one-chip oscillator and clock circuitry. In addition, the AT89C51 is designed with static logic for operation down to zero frequency and supports two software selectable power saving modes. The Idle Mode stops the CPU while allowing the RAM, timer/counters, serial port and interrupt system to continue functioning. The Power-down Mode saves the RAM contents but freezes the oscillator disabling all other chip functions until the next hardware reset.Pin DescriptionVCC:Supply voltage.GND:Ground.Port 0Port 0 is an 8-bit open-drain bi-directional I/O port. As an output port, each pin can sink eight TTL inputs. When 1s are written to port 0 pins, the pins can be used as high-impedance inputs.Port 0 may also be configured to be the multiplexed address/data bus during accesses to external program and data memory. In this mode P0 has internal Pull-up resistor.Port 0 also receives the code bytes during Flash programming,and outputs the code bytes during Program verification. External Pull-up resistors are required during Program verification.Port 1Port 1 is an 8-bit bi-directional I/O port
您可能关注的文档
最近下载
- 管理学-PPT课件(全).pptx
- 高峰数字(四)_原创精品文档.pdf VIP
- “深圳工匠杯”深圳市第十四届职工技术创新运动会暨2024年深圳技能大赛碳排放管理员技能竞赛理论题库及答案(300题).docx VIP
- 粉针剂包装技术与设备.pptx
- 全文解读新修订的2021《中国共产党统一战线工作条例》ppt精品.pptx VIP
- 白蚁防治服务合同协议书范本.docx VIP
- (2022年新版)义务教育初中英语课程标准详细解读 (新课标解读讲座培训课件).pptx VIP
- 湖南《住宅工程质量常见问题防治技术规程》.docx
- 葡萄酿酒有限公司生产安全事故应急预案.docx VIP
- 路基爆破设计及施工组织方案.doc
文档评论(0)