10000m3d印染废水理工程方案设计-环境工程毕业论文.doc

毕业设计：正文 学生姓名：*** 定稿时间：2016-05-05毕业论文（设计）正文题目：10000m3/d印染废水处理工程方案设计Design of 10000m3学 院：环境科学与工程专 业：环境工程班 级：学 号：学生姓名：***指导教师：*** 二○一六年五月10000m3摘 要:本文对浙江一家专业从事染整加工和伞面绸生产的民营企业印染废水处理工程进行方案设计。设计规模为10000m3/d，进水水质COD≤1000 mg/L，BOD≤250 mg/L，SS≤200 mg/L，色度≤500倍。产品以涤纶为主，无单独高浓度废水。设计采用水解酸化+生物接触氧化作为主体工艺，出水可以达到《纺织染整工业水污染物排放标准》（GB 4287-2012）中的新建企业直接排放标准。关键词：印染废水；水解酸化；生物接触氧化Design of 10000m3/d printing and dyeing wastewater trAbstract: In this paper, a professional silk dyeing processing and production of private enterprises umbrella printing and dyeing wastewater treatment program designed in Zhejiang .The designed scale is 10000m3/d, and the average concentration of COD , BOD, SS , Chroma from inflow are less than 1000 mg/L,250 mg/L,200 mg/L and 500 times respectively. Polyester fibre is the main products, with no separated high-strength concentration of wastewater. Hydrolysis acidification and biological contact oxidation was designed as the main technology, the effluent concentration of COD, BOD, SS, Chroma is less than 200 mg/L,50 mg/L,100 mg/L aKey words: Printing and dyeing wastewater; Hydrolytic acidification; Biological contact oxidation目录TOC \o 1-4 \h \u HYPERLINK \l _Toc23643 1. 引言 Ⅰ﹣ PAGEREF _Toc23643 1 HYPERLINK \l _Toc13594 1.1 设计背景及意义 Ⅰ﹣ PAGEREF _Toc13594 1 HYPERLINK \l _Toc13978 1.2 处理技术分析 Ⅰ﹣ PAGEREF _Toc13978 1 HYPERLINK \l _Toc9105 1.3 设计思路 Ⅰ﹣ PAGEREF _Toc9105 2 HYPERLINK \l _Toc2612 2. 项目概述 Ⅰ﹣ PAGEREF _Toc2612 2 HYPERLINK \l _Toc2017 2.1 设计原则 Ⅰ﹣ PAGEREF _Toc2017 2 HYPERLINK \l _Toc2953 2.2 设计依据 Ⅰ﹣ PAGEREF _Toc2953 3 HYPERLINK \l _Toc5685 2.3 设计任务 Ⅰ﹣ PAGEREF _Toc5685 3 HYPERLINK \l _Toc21051 2.3.1 设计水质水量 Ⅰ﹣ PAGEREF _Toc21051 3 HYPERLINK \l _Toc29502 2.3.2 设计排放标准 Ⅰ﹣ PAGEREF _Toc29502 4 HYPERLINK \l _Toc5472 2.4 设计基础资料 Ⅰ﹣ PAGEREF _Toc5472 4 HYPERLINK \l _Toc21028 2.4.