铝合金型材挤压模具的设计方案1.docVIP

课件之家精心整理资料--欢迎你的欣赏 课件之家精心整理资料--欢迎你的欣赏 说明 欲获取全套论文请点击以下链接下载： HYPERLINK /.html /.html 豆丁上面供预览。删去了论文中的图片。完整的论文该有的图都有。包括开题报告；翻译；答辩的PPT；大部分有PCB或DWG文件==。 摘要 针对建筑门窗铝合金空心型材进行了平面分流模设计，分析了平面分流模的各种结构要素及设计要求，并结合实际生产给出了空心挤压型材模具的详细设计方法、设计过程、设计要点、设计流程。实践证明，设计的模具结构合理，获得了好评，因为只有通过对所设计的系统进行分析，才能确定其性能是否满足设计要求。因此，不进行分析和优化就不能进行综合，对于铝型材产品挤压模具设计，更应该如此。随着社会各行业的飞速发展，型材断面形状随之复杂化、多样化，按常规常见形式设计，存在许多不足。所以，要得到优质型材，就得在生产、生活中不断地学习、积累，不断地改造和创新。 关键词：铝合金型材；挤压；平面分流模；模具设计 Abstract A porthole die for forming the aluminum alloy hollow section used in doors and Electnic was developed.Each structuctural element of the die and the design requirements analyzed systematically .Then the method, the key points and process in designing the extrusion die for the hollow section were detemined.，After the problem has been defined and a set of written and impliedspecifications has been obtained,the next step in design is the synthesis of and optimization because the system under design must be analyzed to determint whether the perrormance complies with the specifications. After the problem has been defined and a set of written and impliedspecifications has been obtained,the next step in design is the synthesis of and optimization because the system under design must be analyzed to determint whether the perrormance complies with the specifications. Key words: aluminum alloy section; extrusion; porthole die ; die design. 目录 TOC \o 1-3 \h \z \u HYPERLINK \l _Toc 摘要 PAGEREF _Toc \h 1 HYPERLINK \l _Toc 目录 PAGEREF _Toc \h 3 HYPERLINK \l _Toc 1 绪论 PAGEREF _Toc \h 4 HYPERLINK \l _Toc 2挤压件的尺寸分析 PAGEREF _Toc \h 5 HYPERLINK \l _Toc 2.1 挤压机吨位的选择 PAGEREF _Toc \h 7 HYPERLINK \l _Toc 2.2外形尺寸的确定原则 PAGEREF _Toc \h 7 HYPERLINK \l _Toc 3模孔尺寸的合理计算 PAGEREF _Toc \h 8 HYPERLINK \l _Toc 3.1模具设计的技术条件及基本要求 PAGEREF _Toc \h 9 HYPERLINK \l _Toc 3.2普通型材模具的变化 PAGEREF _Toc \h 10 HYPERLINK \l _Toc 3.3 单孔挤压型材时的模孔配置 PAGEREF _Toc \h 10 HYPERLINK \l _Toc 3.4多孔挤压型材时的模孔配置 PAGEREF _Toc \h 14 HYPERLINK \l _Toc 4分流孔的形状、数目及其分布