施工测量放线方法(阿海珐).docVIP

施工测量专项方案 中国建筑七局有限公司 - PAGE 13 - 目 录 一、编制依据：············································2 1-1、图纸依据：········································2 1-2、测量依据：·········································2 1-3、规程依据：·········································2 二、工程概况：·············································2 三、测量人员及仪器配置：···································3 四、内业准备：··············································4 4.1 人员培训··········································４ 4.2图纸阅读···········································４ 五、平面控制············································５ 5.1基础部分的平面控制；·······························６ 5.2轴线投测；·········································６ 5.3基槽开挖；·········································７ 5.4基础撂底；·········································７ 六、高程控制：············································８ 七、地脚螺栓测量·········································8 八、柱子安装时的测量:·····································10九、吊车梁安装测量：·······································11 十、测量管理制度：········································ 12 十一、测量监控及验线：···································· 12 一、编制依据 1.1．图纸依据： 施工总平面定位图、工程设计图纸目录如下： 序号 图纸名称 图纸编号 1 总平面布置图 765.ZTO.1 1.2．测量依据： 中国新时代国际工程公司提供的临时水准点及平面坐标成果表 1.平面坐标系统：武汉城市坐标系. Xm01: x=3399709.612 y=553994.487 h=54.756 Xm02: x=3399709.418 y=553676.377 h=54.129 eq \o\ac(○,1): x=3399032.162 y=553583.036 定位点1 eq \o\ac(○,2): x=3398826.822 y=553583.036 定位点2 eq \o\ac(○,3): x=3399032.162 y=553673.376 定位点3 2.高程系统：1985国家高程基准. 1.3．规程依据： 《工程测量规范》（GB50026-93） 二：工程概况 本工程位于武汉阳逻经济开发区宝露棉公司南侧，东邻余泊北路，南侧约700米处为汉施公路。工程占地面积为128276.459 主厂房概况 厂房主体单层，平面上分五个区，A区跨度35m，B区五跨跨度分别为23m、21m、21m、27m、18.66m，C区三跨跨度分别为18m、33m、18m，D区跨度18m，E区跨度25m，厂房内局部两层，±0.00标高对应的绝对高程为37.9m，建筑高度11.75m～31.0m，试验站高度33.0m，结构形式为钢排架钢框架结构。 办公楼概况： 办公楼为三层现浇钢筋砼框架结构，平面呈“L”形,东西方向长度为96.04m,南北方向长度为37.4m,±0.00标高对应的绝对高程为35.45m，女儿墙顶高度12.9m,，屋面高度为12.0m，一至三层层高分别为4.2m、3.9m、3.9m。