桥梁博士计算书模板.docxVIP

桥梁博士计算书模板 　　篇一：路桥CAD课程考试桥梁博士计算书(截图) 　　《路桥CAD》 课程考试  　　桥梁博士软件应用 净跨径27m的简支箱梁计算  　　学生姓名： 符健  　　班级： 桥梁1班学号： XX5974 　　目 录 　　一、建模信息·············································3  　　1、结构信息····················································3 2、单元信息·····················································4  　　3、冲击系数计算················································6 4、荷载信息····················································6 5、边界条件····················································7  　　二、单项荷载引起的内力····································7  　　1、重力·························································7 2、施工阶段 预应力··············································7 3、使用阶段 预应力··············································8 4、二期恒载·····················································9 5、汽车Max····························(转 载 于: 小 龙文 档 网:桥梁博士计算书模板)·························9 6、汽车Min·····················································10  　　三、荷载组合·············································11  　　1、承载能力极限状态组合·········································11 2、正常使用极限状态短期效应组合································13 3、正常使用极限状态长期效应组合································16  　　路桥CAD课程考试桥梁博士计算书  　　一、建模信息  　　1、结构信息  　　 本次设计的菩提东路跨河桥跨越俞家河沟，桥梁结构形式为单跨计算跨径为27m的简支箱梁。桥梁起点桩号为K3+，桥面设计高程为；终点桩号为K3+，桥面设计高程为；桥面总体宽度为: (人行道)+ (车行道) + (人行道)=。  　　 桥面建模总体宽度为:(车行道)，此处桥博计算未计入人行道边箱梁。如图：  　　图1 跨中截面  　　图2 变化截面  　　图3 端截面  　　 主梁采用C50现浇,为预应力混凝土简支箱梁。容重：?＝ kN/m3。 设计荷载：  　　汽车：按公路Ⅰ级设计；人群：此处不考虑人群荷载。 设计规范  　　《公路工程技术标准》(JTG B01—XX) 《公路桥涵设计通用规范》(JTG D60-XX)  　　《公路钢筋混凝土及预应力混凝土桥涵设计规范》(JTG D62-XX) 　　《公路桥涵地基与基础设计规范》（JTG D63-XX） 《公路桥涵施工技术规范》（JTJ041－XX） 　　《预应力混凝土桥梁用塑料波纹管》（JT-T529-XX） 《预应力筋用锚具、夹具和连接器》（GBT 14370-XX） 《预应力混凝土用钢绞线》（GB/T 5224-1995） 主要材料及计算参数 混凝土  　　C50混凝土，用于上部预应力混凝土结构  　　弹性模量：×104 MPa，剪切模量：×104 MPa；  　　轴心抗压强度设计值：fcd＝，轴心抗拉强度设计值：ftd＝；  　　泊桑比：； 线膨胀系数: ×10-5 /℃ ； 容重：? ＝ kN/m3 普通钢筋  　　HRB335钢筋：抗拉设计强度弹性模量  　　Es  　　fsd  　　＝280MPa，标准强度  　　fsk  　　＝335MPa，  　　＝×105MPa。  　　R235钢筋：抗拉设计强度fs