单层超大层高大跨重载工业建筑结构体系关键技术研究-结构工程专业论文.docx

Master Dissertation of Suzhou University of Science and Technology Key technologies of single-layer super-storey large cross-overloaded industrial building structure system Master Candidate: Han Changbiao Supervisor: Prof. Dai Yaping A.Prof. Fang Youzhen Major:Structure Engineering Suzhou University of Science and Technology School of Civil Engineering June,2012 苏州科技学院硕士学位论文摘要 苏州科技学院硕士学位论文 摘要 Ⅰ Ⅰ 摘 要 近年来钢管混凝土结构在我国得到了广泛的应用，国家电器产品质量监督检验 中心采用的即为四肢钢管混凝土格构柱结构，格构柱上下柱连接节点采用的是双 向肋板加劲式穿心板肩梁，而对此类肩梁的设计并无规范可依循。为了验证该工 程中肩梁设计方法的准确性，本文以此工程为原型结构，考虑腹板厚度和加劲布 置按1:3缩尺设计制作了3个肩梁连接节点试件并进行了单调加载试验；试验结果显 示，肩梁腹板厚度是影响肩梁抗剪受力性能和破坏模式的关键因素，而加劲布置 方式只在有限范围内提高肩梁的承载能力和改善其传力机理。 此外，本文还利用大型有限元分析软件ANSYS对试件模型结构进行有限元计算 分析，计算结果和试验吻合较好，这也充分显示所建立的有限元模型的合理性。 在此基础上，又进一步针对国家电器产品质量监督检验中心的肩梁建立了有限元 模型，通过调整肩梁腹板厚度、改变加劲肋的位置两种途径对此类肩梁做有限元 计算，结果也进一步表明肩梁腹板厚度是影响肩梁承载力和破坏形态的主要因素， 并深入分析了肩梁腹板应力分布规律及破坏形态，研究成果为相关研究与工程设 计提供理论参考。 关键词：钢管混凝土柱，肩梁，单调加载试验，抗剪性能，破坏模式，有限 元分析 论文类型：应用基础研究 本论文课题来源为苏州市市级建设项目（2010001） 苏州科技学院硕士学位论文A 苏州科技学院硕士学位论文 Abstract Ⅱ Ⅱ Abstract Concrete-filled steel tube has been researched and applied in civil engineering increasingly in recent years. Take National electrical appliances product quality supervision and inspection center which located for example, its industrial building was built with four component built-up CFST columns; The up and down column was connected by shoulder beams with web plate cross the column and reinforced with steel plate two ways, but there is no specification to according to. In order to validate the engineering design method and the accuracy of the shoulder beam, prototype structure were taken ,web thickness and reinforced with steel plate layout were taken as the design parameters. Then the test of 3 specimens designed and fabricated by 1:3 scale which represented the shoulder beam connection were conducted under monotonic loading. The conclusion showed that the web thickness of shoulder beam is more obviously affecting the shear behavior and the failure mode, however stiffening layou