某铸造工艺说明书..docVIP

PAGE PAGE 4 目录 TOC \o 1-3 \h \z \u HYPERLINK \l _Toc345350301 一、铸造方案的选择及工艺参数的设计 PAGEREF _Toc345350301 \h 1 HYPERLINK \l _Toc345350302 1.铸造工艺方案的确定 PAGEREF _Toc345350302 \h 1 HYPERLINK \l _Toc345350303 1．1支座结构的铸造工艺性 PAGEREF _Toc345350303 \h 1 HYPERLINK \l _Toc345350304 1.2造型，造芯方法的选择 PAGEREF _Toc345350304 \h 2 HYPERLINK \l _Toc345350305 1.3浇注系统的设计 PAGEREF _Toc345350305 \h 3 HYPERLINK \l _Toc345350306 1.3.1选择浇注系统类型 PAGEREF _Toc345350306 \h 3 HYPERLINK \l _Toc345350307 1.3.2浇注位置的确定 PAGEREF _Toc345350307 \h 3 HYPERLINK \l _Toc345350308 1.3.3分型面的选择 PAGEREF _Toc345350308 \h 3 HYPERLINK \l _Toc345350309 1.3.4计算浇注时间 PAGEREF _Toc345350309 \h 5 HYPERLINK \l _Toc345350310 1.3.5计算阻流截面积 PAGEREF _Toc345350310 \h 5 HYPERLINK \l _Toc345350311 1.3.6确定浇口比 PAGEREF _Toc345350311 \h 6 HYPERLINK \l _Toc345350312 1.3.7计算内浇道截面积 PAGEREF _Toc345350312 \h 6 HYPERLINK \l _Toc345350313 1.3.8计算横浇道截面积 PAGEREF _Toc345350313 \h 6 HYPERLINK \l _Toc345350314 1.3.9计算直浇道截面积 PAGEREF _Toc345350314 \h 7 HYPERLINK \l _Toc345350315 1.3.10浇口窝的设计 PAGEREF _Toc345350315 \h 8 HYPERLINK \l _Toc345350316 1.3.11浇口杯的设计 PAGEREF _Toc345350316 \h 8 HYPERLINK \l _Toc345350317 2.铸造工艺参数及砂芯设计 PAGEREF _Toc345350317 \h 8 HYPERLINK \l _Toc345350318 2.1 工艺设计参数确定 PAGEREF _Toc345350318 \h 9 HYPERLINK \l _Toc345350319 2.1.1铸件尺寸公差 PAGEREF _Toc345350319 \h 9 HYPERLINK \l _Toc345350320 2.1.2机械加工余量 PAGEREF _Toc345350320 \h 9 HYPERLINK \l _Toc345350321 2.1.3铸造收缩率 PAGEREF _Toc345350321 \h 10 HYPERLINK \l _Toc345350322 2.1.4起模斜度 PAGEREF _Toc345350322 \h 10 HYPERLINK \l _Toc345350323 2.1.5铸件重量公差 PAGEREF _Toc345350323 \h 10 HYPERLINK \l _Toc345350324 2.1.6工艺补正量 PAGEREF _Toc345350324 \h 10 HYPERLINK \l _Toc345350325 2.1.7分型负数 PAGEREF _Toc345350325 \h 11 HYPERLINK \l _Toc345350326 2.1.8反变形量 PAGEREF _Toc345350326 \h 11 HYPERLINK \l _Toc345350327 2.1.9非加工壁厚负余量 PAGEREF _Toc345350327 \h 11 HYPERLINK \l _Toc345350328 2. 2砂芯设计 PAGEREF _Toc345350328 \h 11 HYPERLINK \l _Toc345350329 二、铸造工艺装