毕业设计-金属冷喷涂..docVIP

  1. 1、原创力文档(book118)网站文档一经付费(服务费),不意味着购买了该文档的版权,仅供个人/单位学习、研究之用,不得用于商业用途,未经授权,严禁复制、发行、汇编、翻译或者网络传播等,侵权必究。。
  2. 2、本站所有内容均由合作方或网友上传,本站不对文档的完整性、权威性及其观点立场正确性做任何保证或承诺!文档内容仅供研究参考,付费前请自行鉴别。如您付费,意味着您自己接受本站规则且自行承担风险,本站不退款、不进行额外附加服务;查看《如何避免下载的几个坑》。如果您已付费下载过本站文档,您可以点击 这里二次下载
  3. 3、如文档侵犯商业秘密、侵犯著作权、侵犯人身权等,请点击“版权申诉”(推荐),也可以打举报电话:400-050-0827(电话支持时间:9:00-18:30)。
  4. 4、该文档为VIP文档,如果想要下载,成为VIP会员后,下载免费。
  5. 5、成为VIP后,下载本文档将扣除1次下载权益。下载后,不支持退款、换文档。如有疑问请联系我们
  6. 6、成为VIP后,您将拥有八大权益,权益包括:VIP文档下载权益、阅读免打扰、文档格式转换、高级专利检索、专属身份标志、高级客服、多端互通、版权登记。
  7. 7、VIP文档为合作方或网友上传,每下载1次, 网站将根据用户上传文档的质量评分、类型等,对文档贡献者给予高额补贴、流量扶持。如果你也想贡献VIP文档。上传文档
查看更多
沈阳工业大学硕士学位论文格式规范 PAGE - - PAGE I 摘 要 针对镁合金表面防腐、耐磨的需要,利用冷喷涂技术在镁合金表面制备了耐磨和防腐涂层。为了提高冷喷涂效率,本文根据流体力学和空气动力学的相关理论对超音速喷枪进行优化设计。应用FLUENT软件对拉瓦尔喷枪内的气固两相流动过程进行数值模拟,并对喷枪内气相和固相颗粒的速度、温度和压强分布进行分析,跟据模拟结果改进喷枪结构,使强化材料流出速度达到最佳。 冷喷涂技术的关键是通过拉瓦尔喷枪加速气流提高粉末的喷出速度,实现在基体表面的沉积。气体进口参数对出口气流速度有一定影响。在相同的喷枪结构下,进口速度的变化对出口速度的影响较小,尤其是进口速度低于50m/s时,其变化基本上不会使出口速度有大的改变。并且让进口气流压强有大的提高不易实现。提高出口速度的方式是以提高进口气体温度为主,适当提高进口压强。通过对模拟数据的分析,适当延长喷枪渐扩段的长度既可以降低出口温度,又可以提高出口速度。为了对喷枪内气体流动过程有更深入的分析,应用重整化群(RNG)k–ε模型对喷枪内流动过程进行数值模拟,对喷枪流道形状的变化,采用不均匀网格划分计算区域,并用二阶差分格式离散通用微分方程的对流相;然后用SIMPLE算法来求解气体的运动。跟据上述原理应用fluent软件对喷枪内的压强、温度、速度的分布做分析后,设计出最优的喷枪结构为:入口直径D1=15.2mm,出口直径D2=14mm,喉部半径Rcr=3.5mm;渐缩角α=30°,长度L1=20.9mm;渐扩角 β=10°,渐扩段长度L2=55mm;总长L=75.9mm。然后,对优化设计的喷枪进行数值模拟,得出最后 关键词:镁合金;拉瓦尔喷枪;(RNG)k–ε模型;SIMPLE算法 PAGE II Abstract In order to study the cold spray technology on Mg alloy surface, the designed supersonic nozzle is optimized according to the theory of hydrodynamics and aerodynamics. The FLUENT software is used to simulate the gas-solid flow. The velocity, temperature and pressure of gas and solid particles are analyzed in the Laval Nozzle. According to the simulation results, the nozzle structure is improved to make the velocity of gas and particle best. The key of Cold Spray technology is accelerating the velocity of materials to supersonic in the Laval nozzle, then the powder of materials is deposited on the surface effectively. The speed of outlet was impacted by inlet parameters. At the same Laval nozzle structure, the speed of inlet less impact on outlet speed, particularly inlet velocity blow 50m / s. And increasing air pressure of inlet deeply is difficult realization. The main method of raising the speed of outlet is getting up the gas temperature of inlet with suitable pressure. Through analysis the data of simulation, appropriately extending the length of expanding nozzle’s zone can obtain both lower temperature and higher speed at outlet. A k-ε (RNG) model was used in the simulation in order to understand the cha

文档评论(0)

wyjy + 关注
实名认证
文档贡献者

该用户很懒,什么也没介绍

1亿VIP精品文档

相关文档