《液压阀弹簧座冲压工艺分析及模具设计》-毕业论文设计（学术）.docVIP

摘要 洛阳理工学院毕业设计（论文） PAGE IV PAGE I 液压阀弹簧座冲压工艺分析及模具设计 摘 要 本课题认真分析了液压阀弹簧座的结构和成形工艺，计算了毛坯尺寸和冲压力的大小。设计了排样图及模具结构和尺寸，说明了模具结构的特点等。 具体分析了复合模单工位正装和落料拉深的工艺，设计了排样图和模具结构图，说明了该模具结构的特点，该模具的上模固定板、下模固定板具有高精度的长寿命，一步成形而且重复装配精度高，可快速定位导料板，卸料板上安装到上模座上。通过这次设计为以后从事模具设计方面打下了很好的基础，同时为在校时了解模具行业的发展方向也时很有必要的. 关键词：模具，冲压，落料，拉深 HYDRAULIC VALVE SPRING SEAT DESIGN OF STAMPING PROCESS ANALYSIS AND DIE DESIGN ABSTRACT Hydraulic valve spring seat of the structure and forming technology is seriously analyzed by this topic. The size of the blank dimensions and impact force was calculated. Layout drawing and the die structure size is designed. Shows the characteristics of die structure, etc Composite modulus of simplex bit suits and blanking, deep drawing process were detailed analyzed. Layout diagram and the die structure were designed. The mould on the fixed mould plate, a lower die plate is of high precision long life, that one step forming and repeated assembly of high precision. It can quickly locate guide plate, stripper plate mounted to the mold base. Through this design for future engaged in mold design has laid a good foundation, at the same time as the school know when the mold profession the development direction of also very be necessary. KEY WORDS: Mold, Stamping, Blanking, Deep drawing 前言 目　录 TOC \o 1-3 \h \z \u HYPERLINK \l _Toc359417520 前　言 PAGEREF _Toc359417520 \h 1 HYPERLINK \l _Toc359417521 第1章 零件的冲压工艺性分析 PAGEREF _Toc359417521 \h 4 HYPERLINK \l _Toc359417522 1.1零件的工艺性分析 PAGEREF _Toc359417522 \h 4 HYPERLINK \l _Toc359417523 1.1.1工件结构分析 PAGEREF _Toc359417523 \h 4 HYPERLINK \l _Toc359417524 1.1.2确定最佳工艺方案 PAGEREF _Toc359417524 \h 4 HYPERLINK \l _Toc359417525 第2章 毛坯计算 PAGEREF _Toc359417525 \h 6 HYPERLINK \l _Toc359417526 2.1修边余量的确定 PAGEREF _Toc359417526 \h 6 HYPERLINK \l _Toc359417527 2.1.1能否一次拉深的判断 PAGEREF _Toc359417527 \h 7 HYPERLINK \l _Toc359417528 2.1.2零件的排样及利用率 PAGEREF _Toc359417528 \h 9 HYPERLINK \l _Toc359417529 2.1.3压力计算，压力中心及压力机的选用 PAGEREF _Toc359417529 \h 10