某厂区室外中压电缆敷设施工方案(中英文) _secret.doc

MV Cable Pulling Construction Plan TDI联合装置-基础设施电气系统安装中压电缆敷设施工方案 B 11/30/ ISSUED FOR COMMENTS 2009 A 11/26/ 2009 ISSUED FOR COMMENTS R Date STATUS PREPARED BY CHECKED BY APPROVED BY e DD/MM/ v YY DOCUMENT REVISIONS 目 录Content TOC \o 1-5 \h \z 一.概况 OVERVIEW 3 工程概况 PROJECT OVERVIEW 3 施工范围 SCOPE OF WORK 4 二.编制依据 COMPILATION BASIS 6 三.施工工艺流程：CONSTRUCTION PROCESS 7 四.前期准备PREPARATIO N 7 技术准备 TECHNICAL PREPARATION 7 材料准备 MATERIAL PREPARATION 8 主要机具准备 MAIN EQUIPMENT PREPARATION 9 作业环境准备 WORK ENVIRONMENT PREPARATION 10 五.敷设施工 WORK OF CABLE PULLING 10 电缆敷设施工工序WORK PROCEDURE 10 机具布置 LAYOUT OF TOOLS 10 电缆的搬运及支架架设 CABLE REMOVAL AND CABLE TRAY 10 卷扬机与滑轮的布置 WINCH AND PULLEY ARRANGEMENT 11 电缆展放 LAY-OFF CABLE 14 电缆敷设、固定 CABLE LAYING AND FIXING 18 六.覆砂盖砖 SPREAD SAND AND COVER BRICKS 19 七.回填土 BACKFILL EARTH 19 八.埋标桩 BURYING STAKE 20 九.挂标志牌 HANGING SIGNS 20 十.质量控制 QUALITY CONTROL 20 主控项目 MASTER ITEMS 20 一般项目 GENERAL ITEMS 21 ^^一.成品保护 FINISHED PROTECTION 22 十二.质量记录 QUALITY RECORD 23 质量保证资料 QUALITY ASSURANCE INFORMATION 23 施工记录 CONSTRUCTION OF RECORD 23 十三.安全生产、文明施工要求和措施SAFETY AND CIVILIZED CONSTRUCTION REQUESTS ANDMEASURES 23 概况 Overview 工程概况 Project Overview Medium Voltage Cable Pulling Work. 本工程涉及三个变电站，分别是现有的220/35kV A472变电站、现有的35/10kV B301S变电站以及新建的35/10kV C581变电站，工作内容为三个变电站之间和从三个变电站接至MV用户的电力电缆、控制电缆、接地电缆的敷设。The project involves threesubstations, namely the existing 220/35kV A472 substation, the existing35/10kV B301S the 35/10kV C581 substation and a new substation. This is thepower, control and grounding cable pulling among three substations and forMV users connected to the three substations. 施工范围 Scope of Work A472 建筑（220/35kV 变电站）出线回路：A472 Building(220/35kV substation) outlet circuit 由A472变电站引出3路35kV出线。其中： 一路引至B301S建筑（35/10kV变电站）原1#主变，原1#主变电缆将抽出，与新增4#主变连接；另两路引至35/10kV C581变电站1#主变和2#主变。回路釆用FS-YJY-26/35kV-1*300mm2单芯电缆，直埋敷设。去C581的两路35kV线路，敷设时沿不同路径，以避免两回线路同时受损。Pull three 35V outgoings from A472substation. Of which: The first outgoing is led to B301S Building (35/10kVsubs