建筑工程测量实验报告实训一.docxVIP

建筑工程测量实验报告实训一 　　工程测量学实验报告　　学院：测绘地理信息学院班级：11-2　　学号：姓名：曾丹丹　　一、实验名称：全站仪坐标放样　　二、实验目的　　1.掌握全站仪定向及坐标放样的方法　　2.上交实验报告，全站仪坐标放样　　三、实验仪器　　每小组实验设备为全站仪1台，反光镜1副，一枚小铁钉。　　四、实验内容　　1.坐标数据采集　　2.后视点坐标检校　　3.坐标点放样　　4.检校各放样点坐标　　五、实验步骤　　1、仪器调水平同经纬仪，开机后目镜转360度使垂直过“0”。　　2、按MENU菜单进入模式　　3、按F2：测量程序。　　4、按S?O、　　5、按F3坐标放样，选择一个文件。　　6、按F1输入测站点，按F4依次输入：N、E、Z，全部输完按ENT。　　7、按F2后依次输入后视点：按F4后桌面显示：输入N、E坐标值后照准棱镜后然后按F3确定后进入坐标放样模式。　　8、按F3放样点：显示放样点名按F3桌面显示：N、E、Z依次输入N、E的坐标值，按ENT。　　9、照准棱镜，按F4继续，当dHR(显示数值归零后)表明放样方向正确。　　10、按F2(距离)键HD：实测的水平距离dHD：对准放样点尚差的水平距离。　　11、按F1进行精测。dHR、dHD、dZ均为0时，则放样点的测设已经完成。　　12、按F4继续下一个点的放样　　六、实验总结　　通过这次实验，我们把理论知识和实践技能很好的联合起来，既巩固了理论知识，又掌握了坐标放样的操作技巧。　　实习报告书　　题目：　　系：　　专业：　　班级：　　姓名：　　学号：工程测量学实习测绘工程张全齐XX5　　XX年01月15日　　实习报告评阅书　　学生姓名：张全齐班级：学号：XX5　　实践教学环节名称：工程测量实习教学时间：XX-1-20～XX-3-22　　综合成绩：　　目录　　0引言································································41实习名称···························································42实习目的···························································43实习安排···························································44实习地点···························································45实习任务···························································46范围及组织情况····················································5　　实习范围··························································5　　组织情况··························································5　　注意事项··························································57测区概况···························································58施测方案及过程····················································5　　带状地形图的测绘及图形输出········································5　　线路中线设计······················································6　　利用全站仪现场放样中线············································6　　根据中线进行纵横断面测量··········································7纵断面测量·······················································7　　横断面测量·······················································7　　绘制纵横断面图·······························