DS3231高精度时钟模块程序.docVIP

. . 　　模块参数：　　1.尺寸:38mm(长)*22mm(宽)*14mm(高)　　2.重量:8g　　3.工作电压:3.3--5.5V　　4.时钟芯片:高精度时钟芯片DS3231　　5.时钟精度:0-40℃范围内,精度2ppm,年误差约1分钟　　6.带2个日历闹钟　　7.可编程方波输出　　8.实时时钟产生秒、分、时、星期、日期、月和年计时，并提供有效期到2100年的闰年补偿　　9.芯片内部自带温度传感器,精度为±3℃　　10.存储芯片:AT24C32(存储容量32K)　　11.IIC总线接口,最高传输速度400KHz(工作电压为5V时)　　12.可级联其它IIC设备,24C32地址可通过短路A0/A1/A2修改,默认地址为0x57　　13.带可充电电池LIR2032,保证系统断电后,时钟任然正常走动 ? 接线说明，以Arduino uno r3为例：　　SCL→A5　　SDA→A4　　VCC→5V　　GND→GND ? 代码部分： #include reg51.h#include intrins.h #define uchar?? unsigned char??#define uint??? unsigned int sbit SDA=P3^6;???? //模拟I2C数据传送位SDA????????sbit SCL=P3^7;???? //模拟I2C时钟控制位SCLsbit INT=P3^2;??????sbit RESET=P3^3; sbit led0=P1^0;sbit led1=P1^1;sbit led2=P1^2;sbit led3=P1^3;sbit led4=P1^4;sbit led5=P1^5;sbit led6=P1^6;sbit led7=P1^7; bit? ack;????????? //应答标志位 #define DS3231_WriteAddress 0xD0??? //器件写地址?#define DS3231_ReadAddress? 0xD1??? //器件读地址 #define DS3231_SECOND?????? 0x00??? //秒#define DS3231_MINUTE?????? 0x01??? //分#define DS3231_HOUR???????? 0x02??? //时#define DS3231_WEEK???????? 0x03??? //星期#define DS3231_DAY????????? 0x04??? //日#define DS3231_MONTH??????? 0x05??? //月#define DS3231_YEAR???????? 0x06??? //年//闹铃1????????????#define DS3231_SALARM1ECOND 0x07??? //秒#define DS3231_ALARM1MINUTE 0x08??? //分#define DS3231_ALARM1HOUR?? 0x09??? //时#define DS3231_ALARM1WEEK?? 0x0A??? //星期/日//闹铃2#define DS3231_ALARM2MINUTE 0x0b??? //分#define DS3231_ALARM2HOUR?? 0x0c??? //时#define DS3231_ALARM2WEEK?? 0x0d??? //星期/日#define DS3231_CONTROL????? 0x0e??? //控制寄存器#define DS3231_STATUS?????? 0x0f??? //状态寄存器#define BSY???????????????? 2?????? //忙#define OSF???????????????? 7?????? //振荡器停止标志#define DS3231_XTAL???????? 0x10??? //晶体老化寄存器#define DS3231_TEMPERATUREH 0x11??? //温度寄存器高字节(8位)#define DS3231_TEMPERATUREL 0x12??? //温度寄存器低字节(高2位)? ? uchar code dis_code[11]={0xc0,0xf9,0xa4,0xb0,?? // 0,1,2,3??????????? 0x99,0x92,0x82,0xf8,0x80,0x90, 0xff};?????? // 4,5,6,7,8,9,off uchar data dis_buf[8];uchar data dis_index;ucha