毕业设计(论文)-数控机床维修实验台故障设置模块设计.doc

毕业设计(论文)-数控机床维修实验台故障设置模块设计.doc

  1. 1、原创力文档(book118)网站文档一经付费(服务费),不意味着购买了该文档的版权,仅供个人/单位学习、研究之用,不得用于商业用途,未经授权,严禁复制、发行、汇编、翻译或者网络传播等,侵权必究。。
  2. 2、本站所有内容均由合作方或网友上传,本站不对文档的完整性、权威性及其观点立场正确性做任何保证或承诺!文档内容仅供研究参考,付费前请自行鉴别。如您付费,意味着您自己接受本站规则且自行承担风险,本站不退款、不进行额外附加服务;查看《如何避免下载的几个坑》。如果您已付费下载过本站文档,您可以点击 这里二次下载
  3. 3、如文档侵犯商业秘密、侵犯著作权、侵犯人身权等,请点击“版权申诉”(推荐),也可以打举报电话:400-050-0827(电话支持时间:9:00-18:30)。
查看更多
PAGE 南京工程学院 康尼学院 本科毕业设计(论文) 题目: 数控机床维修实验台故障设置模块设计 班 级: K数控102 学 号: 学生姓名: 指导教师: 起迄日期: 2014.2~2014.6 设计地点: _ PAGE Graduation Design (Thesis) Module Design of CNC MachineTool Repair Experimental Station Fault Set By Supervised by Senior engineer. School of Automation Nanjing Institute of Technology June, 2014 摘 要 本课题的设计思路是在对数控机床系统控制信号分析的基础上,根据实际中常见的一些数控机床的故障问题,针对传统的数控机床维修试验台的不足,在实验台中加入了故障设置模块。它可使实验时故障设计更加简单快捷,可以设置更多的故障。避免了传统的接线式故障设置的缺点,提高了培训的效果。本设计以AT89S52为核心控制芯片,外接一个 1602显示电路,复位电路,六个按键,时钟电路,上位机通讯电路,四十个继电器控制电路。 本设计通过上位机给故障设置模块发送故障设置数据,然后由单片机处理,再控制继电器列阵的开关,从而实现多种类型、多个故障点的设置。控制结果显示在1602显示器上。 本论文重点介绍了AT89S52单片机模块化设计,电流放大电路,继电器控制电路,Protel软件设计电路图,数控系统信号分析。 关键词:AT89S52单片机;继电器;数控维修实验台;故障设置;模块化 全套设计加扣?3012250582 ABSTRACT The design idea is based on the analysis of NC system, NC machine tools according to the failure of some problems encountered in practice, in view of the deficiency of traditional CNC machine tool repair test bench, in the experiment with fault setting module. It can make the design more simple and quick fault, fault can be set more. Avoid setting connection type fault and the shortcomings of traditional, raise training effect. This design take AT89S52 as the core control chip, an external 1602 display circuit, reset circuit, six buttons, clock circuit, communication circuit, forty relay control circuit. This design by six buttons control signal, then by processing chip, a small current signal to the photoelectric coupler amplification, through the UN283 further amplifies the signal, and then the control switch relay array. Control the result is displayed on the 1602 display. Communication circuit PC can be extended through the software of computer application, MCU control. This paper introduces the AT89S52 MCU module design, a current amplifying circuit, a relay control circuit, software design of Protel circuit, signal analysis of CNC system. Keywords: AT89S52 MCU; relay; NC repair

您可能关注的文档

文档评论(0)

***** + 关注
实名认证
内容提供者

该用户很懒,什么也没介绍

1亿VIP精品文档

相关文档