非球面轮廓测量与析.pptVIP

实际面型As分析 几个方向的轮廓一致性较好 实际面型As分析 中心及边缘部分相差较大，测量时部分方向未过顶点 实际面型误差分析 轮廓误差较小，不同方向面型一致性较好 讨论: 1.面型测量主要反映镜片的哪些参数及特性？ 2.面型测量中哪些因素会影响测量结果？ 3.面型不良与MTF不良有何关系？ 4.除了面型与偏心外，还有哪些因素会影响镜头的MTF？（镜片的内部结构：如应力双折射、材质折射率及色散的均匀性、气泡度、条纹度等） 5.其他问题 谢谢您的聆听！ X Axis Z Axis C B A=Aspherics axis 非球面轴 5) Aspheric Data Fit 实测数据与理论数据拟合 Form Talysurf 测量非球面 A B=Actual profile 实际轮廓 C=Absolute aspheric form 绝对非球面形状 +Z 轴 -Z 轴 -X轴 +X 轴 Aspherics axis 非球面轴线 6) Residual Error After Form Removal 形状去除之后的残余误差 Form Talysurf 测量非球面 D=B-C(Residual error after absolute aspheric form removal) 去除绝对形状后的残余误差 7) Analysis Results 分析结果 Form Talysurf 测量非球面 非球面参数简介 非球面参数简介 Figure(Fig.PV) (形狀誤差 ): Figure is the vertical distance between the least squares fit line and the profile height intersected by the Aspheric axis Fig值是實際轮廓之最小二乘拟合直线与實際轮廓被非球面轴线分割点之间的垂直距离. 非球面参数简介 Pa/Ra(轮廓算术平均偏差? ): Pa is the average absolute deviation of the residuals from the mean line . Analogous to unfiltered surface texture parameter Ra. Pa是相对于中线绝对残余偏差的平均值.类似地,不去除表面结构参数即为Ra. 非球面参数简介 Pt/Rt(轮廓总高度? ): Pt is the maximum peak to valley height of the profile in the assessment length(ln). Analogous to unfiltered surface texture parameter Rt. Pa是指在评定长度内最大轮廓峰高与最大轮廓的谷深间的距离.类似地,不去除表面结构参数即为Rt. 非球面参数简介 Smx(? ): Smx is the maximum surface slope error.This is the maximum difference in angular slope between any two adjacent data points and the best fit least squares reference line:calculated from the total profile. 非球面参数简介 Smn(? ): Smx is the mean surface slope error.This is the average difference in angular slope between any two adjacent data points and the best fit least squares reference line:calculated from the total profile. 非球面参数简介 Tilt(?倾斜 ): Tilt is the angle of the calculated horizontal axis of the component, relative to the traverse unit datum axis. 非球面参数简介 Xp: Xp is the distance of the highest peak from the aspheric axis. Xp是指非球面光轴到轮廓最高点之间的距离。 非球面参数简介 Xt: Xt is the distance