- 1、本文档共24页,可阅读全部内容。
- 2、原创力文档(book118)网站文档一经付费(服务费),不意味着购买了该文档的版权,仅供个人/单位学习、研究之用,不得用于商业用途,未经授权,严禁复制、发行、汇编、翻译或者网络传播等,侵权必究。
- 3、本站所有内容均由合作方或网友上传,本站不对文档的完整性、权威性及其观点立场正确性做任何保证或承诺!文档内容仅供研究参考,付费前请自行鉴别。如您付费,意味着您自己接受本站规则且自行承担风险,本站不退款、不进行额外附加服务;查看《如何避免下载的几个坑》。如果您已付费下载过本站文档,您可以点击 这里二次下载。
- 4、如文档侵犯商业秘密、侵犯著作权、侵犯人身权等,请点击“版权申诉”(推荐),也可以打举报电话:400-050-0827(电话支持时间:9:00-18:30)。
查看更多
General Instructions (Plenum Plug Fan
BNA-ANA- BPA-APA
IGB030.E0/1203
This manual is to guide the users in the proper storage, installation, operation and maintenance procedures to ensure maximum equipment life and trouble-free operation. HANDLING AND MAINTENANCE SHOULD ALWAYS BE PERFORMED BY EXPERIENCED AND TRAINED PERSONNEL.
RECEIVING, HANDLING AND STORAGE
Rough handling during shipment and improper storage can cause damage that is not noticeable until the fan is in operation. This can be avoided with proper storage and handling techniques.
Fan should be hoisted with slings placed around the fan housing. Touch up the scratch coated surfaces during lifting, to prevent corrosion to occur at this area. Store the fan in a clean and dry place, preferably indoor to ensure fan shaft, bearing and fan casing are protected against dust and corrosion. Do not store the fan in a location where it will be subjected to vibration. This can cause the internal surface to rub against each other and damage the bearings.
START-UP CHECK LIST
Before putting any fan into initial operation the manufacturer’s instruction must be followed. Complete the following checklist to make sure that the fan is ready to run.
Lock out the primary and all secondary power sources.
Make sure the foundation or mounting arrangement and the duct
connections are adequately designed in accordance with recognized
acceptable engineering practices and with the fan manufacturer’s
recommendations.
Check and tighten all hold-down (securing bolts.
Check the fan assembly and bearings for proper grounding to prevent
static electricity discharge.
Spin impeller to see whether it rotates freely and is not grossly out of
balance.
Inspect impeller for correct rotation for the fan design.
Check belt drive or coupling alignment, use recommended belt tension.
Check belt drive for proper sheave selection and make sure they are
not reversed.
Properly secure all safety guards.
Switch on the electrical supply and allow the
您可能关注的文档
- 新闻系学生应加强素质教育.ppt
- 新闻发布的社会职责.ppt
- 新车验车及注意事项验车后完整版_图文.doc
- 新闻评论的回顾与发展.doc
- 新风机参数表.doc
- 方便米粉生产主要原料 大米.ppt
- 方向项目任务书.doc
- 方正{影仪软件操作手册 - 图文-.doc
- 施工升降机操作工应知应会试题.doc
- 施工员,建造师等.doc
- 2024-2030年中国硝酸甘油透皮贴片行业市场发展趋势与前景展望战略分析报告.docx
- 2024-2030年中国石饰面板行业市场发展分析及商业模式与投资前景研究报告.docx
- 2024-2030年中国硼硅玻璃行业市场发展趋势与前景展望战略分析报告.docx
- 2024-2030年中国碳纤维风电叶片行业盈利态势与需求潜力预测报告.docx
- 2024-2030年中国硼铁市场运营状况及投资前景预测报告.docx
- 2024-2030年中国童装行业市场发展分析及发展前景与投资研究报告.docx
- 2024-2030年中国空心漂珠市场运行现状及发展前景预测报告.docx
- 2024-2030年中国立式健身车行业市场发展趋势与前景展望战略分析报告.docx
- 2024-2030年中国碳化硅涂层石墨基座行业运行态势及投资趋势预测报告.docx
- 2024-2030年中国眼底成像系统行业市场发展趋势与前景展望战略分析报告.docx
文档评论(0)